#ifndef __VAR_H #define __VAR_H #include "stm32f1xx_hal.h" #include "cadence_sensor.h" #include "stdlib.h" #include "string.h" #include "adc.h" /******************************类型定义Begin*************************/ typedef enum { NoName = 0x00, STM32F103RBT6, APM32F103RBT6, HK32F103RBT6, GD32F103RBT6, APM32F103RCT7 }MCU_Manufacturter_Struct_t; typedef enum { MC_LightSwitch_OFF = 0xF0, MC_LightSwitch_ON = 0xF1 }MC_LightSwitch_Struct_t; //电机运行信息，占用空间32bytes typedef struct { uint16_t BikeSpeed; //车速 0.1km/h，地址偏移0 int16_t MotorSpeed; //输出转速 1rpm，地址偏移2 uint16_t Power; //电功率 1W，地址偏移4 uint16_t BusVoltage; //母线电压 1mV，地址偏移6 uint16_t BusCurrent; //母线电流 1mA，地址偏移8 uint8_t Cadence; //踏频 1rpm，地址偏移10 uint8_t Torque; //踩踏力矩 1Nm，地址偏移11 MC_CadenceDir_Struct_t CadenceDir; //踩踏方向 0-正,1-反,2-停止，地址偏移12 uint8_t GearSt; //助力档位，地址偏移13 MC_LightSwitch_Struct_t LightSwitch; //灯开关 0xF0-关，0xF1-开，地址偏移14 uint8_t SOC; //剩余电量 1%，地址偏移15 uint16_t RemainDistance; //续航里程 1km，地址偏移16 uint16_t ODO_Km; //总里程 1km，地址偏移18 uint8_t PowerPerKm; //平均功耗 0.01Ah/km ，地址偏移20 uint8_t T_PCB; //PCB温度 +40℃，地址偏移21 uint8_t T_Coil; //绕组温度 +40℃，地址偏移22 uint8_t T_MCU; //MCU温度 +40℃，地址偏移23 uint16_t Ride_Km; //开机后骑行里程 0.1km, 地址偏移24 uint16_t Ride_Time; //开机后骑行时间 1s，地址偏移26 uint8_t TorqueSensorData1; //力矩传感器1原始值 uint8_t TorqueSensorData2; //力矩传感器2原始值 uint8_t TorqueSensorData3; //力矩传感器3原始值 uint8_t GearBoxInfo; //自动变速器运行信息 1byte }MC_RunInfo_Struct_t; //电机调试信息，占用空间32bytes typedef struct { uint8_t SysFSM1; //系统功能状态机1，赋值助力模式 uint8_t SysFSM2; //系统功能状态机2，赋值助力模式 uint8_t SysFSM3; //系统功能状态机3，赋值助力模式 uint8_t SysFSM4; //系统功能状态机4，赋值助力模式 int16_t IdRef; //D轴参考电流 int16_t IqRef; //Q轴参考电流 int16_t UdRef; //D轴参考电压 int16_t UqRef; //Q轴参考电压 uint16_t PedalTorquePer; //踩踏瞬时力矩 uint16_t PedalTorqueAvg; //踩踏时域滤波力矩 uint16_t PedalTorqueByCad; //踩踏踏频滤波力矩 int16_t IdFdb; //D轴反馈电流 int16_t IqFdb; //Q轴反馈电流 uint16_t AssistOut; //助力输出值 uint8_t RS[8]; }MC_DebugInfo_Struct_t; //电机故障码，占用空间4bytes typedef union { struct { uint32_t Protect_OverCurrent :1;//过流保护 uint32_t Protect_UnderVoltage :1;//低压保护 uint32_t Protect_OverVoltage :1;//过压保护 uint32_t Protect_LockRotor :1;//堵转保护 uint32_t Protect_OverTemp :1;//过热保护 uint32_t Fault_SpeedSensor :1;//速度传感器故障 uint32_t Fault_TorqueSensor :1;//力矩传感器故障 uint32_t Fault_HallSensor :1;//霍尔传感器故障 uint32_t Fault_PhaseLine :1;//相线故障 uint32_t Fault_NtcSensor :1;//温度传感器故障 uint32_t Fault_BMS_Check :1;//BMS校验失败 uint32_t Fault_HMI_Check :1;//HMI校验失败 uint32_t Fault_PBU_Check :1;//PBU校验失败 uint32_t Fault_MCU :1;//MCU故障 uint32_t Fault_CadenceSensor :1;//踏频传感器故障 uint32_t Fault_GasSensor :1;//指拨故障 uint32_t Fault_MOS :1;//MOS短路 uint32_t Protect_VoltageChange :1;//电压波动异常 uint32_t Fault_Circuit :1;//电路故障 uint32_t Fault_TE_MCU :1;//TE MCU故障 uint32_t Fault_TE_Circuit :1;//TE 电路故障 uint32_t Fault_MC_Check :1;//MC校验失败 uint32_t Fault_Machine :1;//机械故障 uint32_t RS2 :1; uint32_t RS3 :1; uint32_t RS4 :1; uint32_t RS5 :1; uint32_t RS6 :1; uint32_t RS7 :1; uint32_t RS8 :1; uint32_t RS9 :1; uint32_t RS10 :1; }ERROR_Bit; uint32_t Code; }MC_ErrorCode_Struct_t; //在线检测结果，占用空间1byte typedef union ONLINE_STATUS { struct { uint8_t BMS_OffLine :1;//BMS离线 uint8_t PBU_OffLine :1;//PBU离线 uint8_t HMI_OffLine :1;//HMI离线 uint8_t RS1 :1; uint8_t RS2 :1; uint8_t RS3 :1; uint8_t RS4 :1; uint8_t RS5 :1; }Status_Bit; uint8_t Status; }OnLine_Status_Struct_t; //授权校验，占用空间24bytes typedef struct { uint8_t MAC_ID[12]; //物理ID uint8_t CheckCode[12]; //校验码 }Device_CheckInfo_Struct_t; typedef enum STARMODE { NC = 0U, MC_StarMode_SOFT, //1 MC_StarMode_NORM, //2 MC_StarMode_DYNAMIC, //3 }MC_StarMode_Struct_t; typedef struct { uint8_t Assist_K_GAIN; //0.01 80-120 uint8_t StarModel_GAIN; //0.01 80-120 }UserAdjParam1_Struct_t; typedef struct { uint8_t MaxCurrent_K_GAIN; //0.01 80-120 uint8_t MaxTorque_K_GAIN; //0.01 80-120 }UserAdjParam2_Struct_t; typedef enum MC_SUPPORTFLAG { MC_SUPPORT_ENABLE = (uint8_t)0xAA, //支持 MC_SUPPORT_DISABLE = (uint8_t)0x55 //不支持 }MC_SupportFlag_Struct_t; typedef enum MC_SPEED_SIGNAL { MC_SPEED_CADENCE_CAL = (uint8_t)0xAA, //根据踏频估算 MC_SPEED_WHEEL_TRIG = (uint8_t)0x55, //根据车轮信号触发 MC_SPEED_COMMUNICATION = (uint8_t)0xEE //根据通信数据，车轮旋转1圈的时间 }MC_SpeedSignal_Struct_t; typedef enum MC_FRONT_LIGHT_MODE { MC_FRONT_LIGHT_MODE1 = (uint8_t)0x10, //模式1,常亮 MC_FRONT_LIGHT_MODE2 = (uint8_t)0x20, //模式2,仪表控制开关 MC_FRONT_LIGHT_MODE3 = (uint8_t)0x30, //模式3,闪烁（功能预留） }MC_FrontLight_Mode_Struct_t; typedef enum MC_TAIL_LIGHT_MODE { MC_TAIL_LIGHT_MODE1 = (uint8_t)0x01, //模式1,连接尾灯,开灯时低亮,刹车时高亮 MC_TAIL_LIGHT_MODE2 = (uint8_t)0x02, //模式2,连接尾灯,开灯时高亮,刹车时闪烁 MC_TAIL_LIGHT_MODE3 = (uint8_t)0x03, //模式3,连接刹车灯,刹车时高亮 MC_TAIL_LIGHT_MODE4 = (uint8_t)0x04, //模式4,连接刹车灯,刹车时闪烁 MC_TAIL_LIGHT_MODE5 = (uint8_t)0x05, //模式5,常亮 MC_TAIL_LIGHT_MODE6 = (uint8_t)0x06 //模式6,超速报警 }MC_TailLight_Mode_Struct_t; typedef enum MC_LIGHT_VOLTAGE { MC_LIGHT_VOL_6V = (uint8_t)0x06, //灯电压6V MC_LIGHT_VOL_12V = (uint8_t)0x0C, //灯电压12V MC_LIGHT_VOL_BATTERY = (uint8_t)0xFF //灯电压随电池电压 }MC_LightVoltage_Struct_t; typedef union GAS_MODE { struct { uint8_t CrontrolMode :1; //0-速度模式，1-力矩模式 uint8_t PowerLimitFlag :1; //0-不根据挡位限制，1-根据挡位限制 uint8_t StartMode :1; //0-零速启动，1-带速启动 uint8_t SpeedLimit :5; //车速限制 }Mode_bit; uint8_t Mode; //0x55-不支持转把模式 }MC_GasMode_Struct_t; //用户配置参数1，占用空间32bytes typedef struct { uint8_t GasCtrlMode_Param; //指拨模式参数，地址偏移0 MC_StarMode_Struct_t StarModel; //启动模式，地址偏移1 uint16_t StopTime; //停机时间 ms，地址偏移2 uint8_t SpeedLimit; //限速 km/h，地址偏移4 uint8_t Deceleration; //下降速度，地址偏移5 uint8_t TeethNum_F; //前齿数 T，地址偏移6 uint8_t TeethNum_B; //后齿数 T，地址偏移7 uint8_t CurrentLimit; //限流 A，地址偏移8 uint8_t TempTH_Alarm; //高温预警值 +40℃，地址偏移9 uint8_t TempTH_Protect; //高温保护值 +40℃，地址偏移10 MC_SupportFlag_Struct_t NoPBU_Flag; //0x55-不支持，0x-AA支持，地址偏移11 uint8_t WheelSize; //轮胎周长 cm，地址偏移12 uint8_t SerialNum; //系列号，地址偏移13 UserAdjParam1_Struct_t UserAdjParam1_ECO; //用户微调助力比增益和加速度增益，地址偏移14 UserAdjParam1_Struct_t UserAdjParam1_NORM; //用户微调助力比增益和加速度增益，地址偏移16 UserAdjParam1_Struct_t UserAdjParam1_SPORT; //用户微调助力比增益和加速度增益，地址偏移18 UserAdjParam1_Struct_t UserAdjParam1_TURBO; //用户微调助力比增益和加速度增益，地址偏移20 UserAdjParam1_Struct_t UserAdjParam1_SMART; //用户微调助力比增益和加速度增益，地址偏移22 uint8_t SpeedSensorPoles; //速度传感器极数，地址偏移24 uint8_t CadenceStarNum; //踏频启动信号个数，地址偏移25 MC_SpeedSignal_Struct_t SpeedSignal; //0x55-车轮触发，0x-AA踏频计算，0xEE-通讯获取车轮旋转周期，地址偏移26 int8_t WheelSizeAdj; //周长微调值，地址偏移27 uint16_t UV_Protect_TH; //低压保护值，地址偏移28 uint8_t WalkMode_SpeedLimit; //推行模式限速，地址偏移30 uint8_t WalkMode_MotorSpeedSet; //推行模式电机转速设置，地址偏移31 }MC_ConfigParam1_Struct_t; //用户配置参数2，占用空间32bytes typedef struct { int16_t ZeroAngle_Pitch; //俯仰角零度偏移，地址偏移0 int16_t ZeroAngle_Roll; //横滚角零度偏移，地址偏移2 MC_SupportFlag_Struct_t UseAttitudeAngle_Flag; //支持姿态角度传感器标志，地址偏移4 uint8_t MC_Light_Mode; //前后灯功能，地址偏移5 MC_LightVoltage_Struct_t HeadLightVol; //前灯电压，地址偏移6 MC_LightVoltage_Struct_t TailLightVol; //后灯电压，地址偏移7 uint16_t u16OverspeedWarnVal; //超速告警值，地址偏移8 uint16_t u16EffectVal; //尾灯亮起有效值，地址偏移10 uint16_t u16Prediv; //尾灯亮起时间的分频系数，地址偏移12 int8_t SpeedLimitStartAdj; //起始限速微调，默认0，从限速值开始衰减，地址偏移13 int8_t SpeedLimitEndAdj; //结束限速微调，默认0，从限速值+2.2km/h结束，地址偏移14 int8_t SpeedLimitAdj; //限速微调，默认0，与限速值相同，地址偏移15 uint8_t RS1; //预留，0x00，地址偏移16 UserAdjParam2_Struct_t UserAdjParam2_ECO; //用户微调最大电流增益和最大力矩增益，地址偏移14，地址偏移18 UserAdjParam2_Struct_t UserAdjParam2_NORM; //用户微调最大电流增益和最大力矩增益，地址偏移14，地址偏移20 UserAdjParam2_Struct_t UserAdjParam2_SPORT; //用户微调最大电流增益和最大力矩增益，地址偏移14，地址偏移22 UserAdjParam2_Struct_t UserAdjParam2_TURBO; //用户微调最大电流增益和最大力矩增益，地址偏移14，地址偏移24 UserAdjParam2_Struct_t UserAdjParam2_SMART; //用户微调最大电流增益和最大力矩增益，地址偏移14，地址偏移26 uint8_t RS2[4]; }MC_ConfigParam2_Struct_t; //姿态传感器数值 typedef struct { int16_t Angle_Pitch_Absolute; //俯仰角绝对角度 int16_t Angle_Roll_Absolute; //横滚角绝对角度 int16_t Angle_Pitch_Relative; //俯仰角相对角度 int16_t Angle_Roll_Relative; //横滚角相对角度 }MC_AttitudeAngle_Struct_t; //马达配置参数，占用空间16bytes typedef struct { uint16_t Rate_Power; //W，地址偏移0 uint16_t Rate_Speed; //rpm，地址偏移2 uint16_t Coil_R; //mOhm，地址偏移4 uint16_t Coil_Lq; //mH，地址偏移6 uint16_t Coil_Ld; //mH，地址偏移8 uint16_t Back_EMF; //Peak Voltage, mV@1000rpm，地址偏移10 uint8_t Rate_Voltage; //Rate Voltage, V，地址偏移12 uint8_t Pole; //极对数 uint8_t RS[2]; }MC_MotorParam_Struct_t; //MC运行历史，占用空间48bytes typedef struct { uint32_t PowerOnCnt; //开机次数，地址偏移0 uint32_t RunTime; //运行总时间 min，地址偏移4 uint16_t OC_ProtectCnt; //过流保次数 ，地址偏移8 uint16_t UV_ProtectCnt; //低压保护次数，地址偏移10 uint16_t OV_ProtectCnt; //高压保护次数，地址偏移12 uint16_t LockRotor_ProtectCnt; //堵转保护次数 ，地址偏移14 uint16_t OT_ProtectCnt; //温度保护次数，地址偏移16 uint16_t SPS_FaultCnt; //速度传感器错误次数，地址偏移18 uint16_t TQS_FaultCnt; //力矩传感器错误次数 ，地址偏移20 uint16_t Hall_FaultCnt; //霍尔传感器错误次数 ，地址偏移22 uint16_t PhaseLine_FaultCnt; //马达相线错误次数，地址偏移24 uint16_t NTC_FaultCnt; //NTC错误次数，地址偏移26 uint16_t BMS_Check_FaultCnt; //BMS校验错误次数，地址偏移28 uint16_t HMI_Check_FaultCnt; //HMI校验错误次数，地址偏移30 uint16_t PBU_Check_FaultCnt; //PBU校验错误次数 ，地址偏移32 uint8_t T_PCB_Max; //PCB历史最高温，地址偏移34 uint8_t T_PCB_Min; //PCB历史最低温，地址偏移35 uint32_t ODO_Km; //出厂后ODO里程，地址偏移36 uint8_t T_Coil_Max; //绕组历史最高温，地址偏移40 uint8_t T_Coil_Min; //绕组历史最低温，地址偏移41 uint8_t T_MCU_Max; //MCU历史最高温，地址偏移42 uint8_t T_MCU_Min; //MCU历史最低温，地址偏移43 uint32_t ODO_Time; //出厂后ODO时间，地址偏移44 }MC_RunLog1_Struct_t; //MC运行历史，占用空间24bytes typedef struct { uint16_t MCU_FaultCnt; uint16_t CadenceSensor_FaultCnt; uint16_t GasSensor_FaultCnt; uint16_t MOS_ShortCircuit_FaultCnt; uint16_t VoltageChangeOrOverSpeed_FaultCnt; uint16_t Circuit_FaultCnt; uint16_t TE_MCU_FaultCnt; uint16_t TE_Circuit_FaultCnt; }MC_RunLog2_Struct_t; //MC骑行历史信息，占用空间16bytes typedef struct { uint32_t ODO_Km; //ODO里程，地址偏移0 uint32_t ODO_Time; //ODO时间，地址偏移4 uint32_t TRIP_Km; //TRIP里程，地址偏移8 uint32_t TRIP_Time; //TRIP时间，地址偏移12 }MC_RideLog_Struct_t; //MC版本信息，占用空间64bytes typedef struct { char Mode[16]; //型号 ASCII，0x2E结束，无效填充0x20 char SN_Num[16]; //序列号 ASCII，0x2E结束，无效填充0x20 char HW_Version[16]; //硬件版本 ASCII，0x2E结束，无效填充0x20 char FW_Version[16]; //软件版本 ASCII，0x2E结束，无效填充0x20 }MC_VerInfo_Struct_t; //MC生产信息，占用空间32bytes typedef struct { char Manufacturer[8]; //生产厂商 ASCII，0x2E结束，无效填充0x20 char MacAddr[8]; //生产地 ASCII，0x2E结束，无效填充0x20 char MacDate[8]; //生产日期 ASCII，0x2E结束，无效填充0x20 char ProductTag[8]; //产品标识 }MC_MacInfo_Struct_t; //MC掉电临时保存数据，占用40bytes typedef struct { uint32_t ODO_Km; uint32_t ODO_Time; uint32_t Trip_Km; uint32_t Trip_Time; uint32_t Run_Time; uint32_t Log_ODO_Km; uint32_t Log_ODO_Time; uint32_t RS[3]; }MC_PowerOffBkp_Struct_t; //电池运行状态，占用空间1bytes typedef union { struct { uint8_t Charge :1;//充电 uint8_t Discharge :1;//放电 uint8_t RS1 :1; uint8_t RS2 :1; uint8_t RS3 :1; uint8_t RS4 :1; uint8_t RS5 :1; uint8_t RS6 :1; }Status_Bit; uint8_t Status; }BMS_STATUS_Struct_t; //电池运行信息，占用空间16bytes typedef struct { uint16_t Voltage; //电压 1mV，地址偏移0 uint16_t Current; //电流 1mA，地址偏移2 uint16_t RC; //剩余容量 1mAh，地址偏移4 uint16_t FCC; //满充容量 1mAh，地址偏移6 uint8_t Cell_NTC; //电芯温度 +40℃，地址偏移8 uint8_t SOC; //剩余电量 1%，地址偏移9 BMS_STATUS_Struct_t Status; //运行状态，地址偏移10 uint8_t RS[5]; }BMS_RunInfo_Struct_t; //BMS设计信息，占用空间16bytes typedef struct { uint16_t Capacity; //电池设计容量，地址偏移0 uint8_t Voltage; //电池设计电压，地址偏移2 uint8_t CellMode[8]; //电芯型号，地址偏移3 uint8_t RS[5]; }BMS_DesignInfo_Struct_t; //电池电芯放电信息，占用空间204bytes typedef struct BATTERY { uint16_t DesignCap; //设计容量 uint16_t CellParam[101]; //电压-SOC曲线 }BatterCellInfo_Struct_t; //PBU配置的参数，占用空间8bytes typedef struct { uint8_t GearsNum; //助力档位数量 MC_SupportFlag_Struct_t NoHMI_Flag; //支持无HMI标识,0x55-不支持，0x-AA支持 uint8_t RS[6]; }PBU_ConfigParam_Struct_t; typedef union TE_ERROR_CODE { struct { uint16_t BikeSpeed :1;//速度传感器， 电路故障 uint16_t TorqueSensor :1;//力矩传感器， 电路故障 uint16_t Current :1;//母线电流， 电路故障 uint16_t T_Coil :1;//绕组温度， 电路故障 uint16_t HallSensor_A :1;//霍尔传感器A， 电路故障 uint16_t HallSensor_B :1;//霍尔传感器A， 电路故障 uint16_t CadenseSensor_1 :1;//踏频传感器1， 电路故障 uint16_t CadenseSensor_2 :1;//踏频传感器2， 电路故障 uint16_t StopBreak :1;//刹车信号， 电路故障 uint16_t VCC :1;//3.3V异常， 电路故障 uint16_t ClockFreq :1;//系统时钟异常， 主控MCU故障 uint16_t ComFault :1;//串口通讯RX故障，主控MCU故障 uint16_t MCUFault :1;//MCU异常， TE MCU故障 uint16_t RS1 :1; uint16_t RS2 :1; uint16_t RS3 :1; }Status_Bit; uint16_t Code; }TE_ErrorCode_Struct_t; //TE传回传感器状态 typedef struct { TE_ErrorCode_Struct_t TE_ErrorCode; uint16_t MCU_Voltage; uint16_t SyncClockFreq; uint16_t RS; }MC_TE_SensorStatus_Struct_t; //发给TE传感器结果 typedef struct { uint16_t AD_Torque; //力矩传感器AD值，地址偏移0 uint16_t AD_BusCurrent; //母线电流AD值，地址偏移2 uint16_t AD_CoilTemp; //绕组温度AD值，地址偏移4 uint16_t AD_TE_Voltage; //TE电压AD值，地址偏移6 uint16_t CadenceHall_1_Cnt; //踏频霍尔1计数，地址偏移8 uint16_t CadenceHall_2_Cnt; //踏频霍尔2计数，地址偏移10 uint16_t MotorHall_A_Cnt; //马达霍尔1计数，地址偏移12 uint16_t MotorHall_B_Cnt; //马达霍尔2计数，地址偏移14 uint8_t BreakTrgiCnt; //刹车计数，地址偏移16 uint8_t SpeedSensorTrigCnt; //速度传感器计数，地址偏移17 uint16_t SynC_Clock_Freq; //地址偏移18 }MC_TE_SensorData_Struct_t; typedef enum _TO_TE_SENDSTEP { HANDSHAKE = 0U, SENDSENSOR, SENDUPDATA, }To_Te_SendStep; //助力计算参数 typedef struct { uint16_t Gain_K; //助力比系数，放大100倍，偏移地址 0 uint16_t TorqueApp_TH; //i-Sport档位力矩阈值，偏移地址 2 uint16_t Lower_Iq; //助力输出下限值，偏移地址 4 uint16_t Upper_Iq; //助力输出上限值，偏移地址 6 uint8_t AccCnt; //力矩控制ref加速斜率, 偏移地址 8 uint8_t DecCnt; //力矩控制ref减速斜率, 偏移地址 9 uint16_t CurrentMax_K; //最大电流 / 限流值百分比, 偏移地址 10 }nGearParam_Struct_t; //n档位控制参数结构体定义 typedef struct { nGearParam_Struct_t Gear_ECO; //ECO档控制参数，偏移地址 0 nGearParam_Struct_t Gear_NORM; //NORM档控制参数，偏移地址 12 nGearParam_Struct_t Gear_SPORT; //SPORT档控制参数，偏移地址 24 nGearParam_Struct_t Gear_TURBO; //TURBO档控制参数，偏移地址 36 nGearParam_Struct_t Gear_SMART; //SMART档控制参数，偏移地址 48 }MC_AssistParam_Struct_t; typedef struct { TrueOrFalse_Flag_Struct_t IsOK_Flag; uint32_t OK_TrigTime; }ComOK_Check_Struct_t; //各个助力档位平均功耗 typedef struct { uint16_t GearSt_ECO; //ECO平均功耗，单位mAh/km uint16_t GearSt_NORM; //NORM平均功耗，单位mAh/km uint16_t GearSt_SPORT; //SPORT平均功耗，单位mAh/km uint16_t GearSt_TURBO; //TURBO平均功耗，单位mAh/km uint16_t GearSt_SMART; //SMART平均功耗，单位mAh/km uint16_t Rs[3]; }MC_AvgPower_Struct_t; //传动比计算参数 typedef struct { uint16_t RatioPer; //实时传动比，车速(km/h) / 电机转速(rpm)* 102400，车速 = 电机转速 / 4.55 * 前牙盘 / 后牙盘 * 轮胎周长 * 60 / 1000 uint16_t RatioFlt; //传动比滤波值 int32_t RatioFltSum; uint16_t TargetAcc; //目标值递增阶梯 uint16_t TargetDec; //目标值递减阶梯 uint16_t RatioDefault; //传动比默認值 uint16_t RatioResult; //传动比输出 }Bike_RatioCal_Struct_t; //硬件版本定义表 extern const uint16_t Ver_Table[11]; /******************************类型定义End***************************/ /**************************全局变量声明Begin*************************/ extern MC_RunInfo_Struct_t MC_RunInfo; extern MC_DebugInfo_Struct_t MC_DebugInfo; extern MC_ErrorCode_Struct_t MC_ErrorCode; extern MC_VerInfo_Struct_t MC_VerInfo; extern char Firmware_Special[32]; extern uint8_t MC_TagInfo[32]; extern OnLine_Status_Struct_t DeviceOnLine_Status; extern BMS_RunInfo_Struct_t BMS_RunInfo; extern Device_CheckInfo_Struct_t BMS_CheckInfo; extern BatterCellInfo_Struct_t BatteryCellInfo; extern BMS_DesignInfo_Struct_t BMS_DesignInfo; extern Device_CheckInfo_Struct_t PBU_CheckInfo; extern PBU_ConfigParam_Struct_t PBU_ConfigParam; extern Device_CheckInfo_Struct_t HMI_CheckInfo; extern MC_GasMode_Struct_t MC_GasMode_Param; extern MC_ConfigParam1_Struct_t MC_ConfigParam1; extern MC_ConfigParam2_Struct_t MC_ConfigParam2; extern MC_MotorParam_Struct_t MC_MotorParam; extern MC_RunLog1_Struct_t MC_RunLog1; extern MC_RunLog2_Struct_t MC_RunLog2; extern uint8_t RunLogSaveIndex; extern uint8_t Secret_Key[8]; extern MC_MacInfo_Struct_t MC_MacInfo; extern uint8_t UserString1[16]; extern uint8_t UserString2[16]; extern uint8_t UserString3[16]; extern MC_PowerOffBkp_Struct_t MC_PowerOffBkp; extern Device_CheckInfo_Struct_t MC_CheckInfo; extern MC_TE_SensorStatus_Struct_t MC_TE_SensorStatus; extern MC_TE_SensorData_Struct_t MC_TE_SensorData; extern uint16_t MC_TE_SyncClockFreqScan; extern TrueOrFalse_Flag_Struct_t TE_MCU_DataRefreshFlag; extern MC_AssistParam_Struct_t MC_AssisParam; extern uint8_t MC_WalkMode_Persent; extern ComOK_Check_Struct_t IsComOK_TE; extern ComOK_Check_Struct_t IsComOK_PBU; extern ComOK_Check_Struct_t IsComOK_HMI; extern ComOK_Check_Struct_t IsComOK_BMS; extern MC_AttitudeAngle_Struct_t MC_AttitudeAngle; extern MC_RideLog_Struct_t MC_RideLog; extern MC_AvgPower_Struct_t MC_AvgPower; extern MCU_Manufacturter_Struct_t MCUManufacturer; extern uint16_t SpeedRatio; extern uint16_t HardwareVersion_AD; extern TrueOrFalse_Flag_Struct_t VersionIdentifyFinishedFlag; extern TrueOrFalse_Flag_Struct_t PowerDown_SaveFlag; extern Bike_RatioCal_Struct_t Bike_RatioCalParam; /**************************全局变量声明End***************************/ /**************************全局函数声明Begin*************************/ extern void Var_Init(void); extern void UpdateGearParam(uint8_t SerialNum); extern void Var_SetToDefaultParam(void); extern void Var_SetToDefaultLog(void); /**************************全局函数声明End***************************/ #endif