motor_ctl-4/User project/3.BasicFunction/Source/i2c_master.c

/************************************************************************
 Project:               Welling Motor Control Paltform
 Filename:              i2c_master.c
 Partner Filename:      i2c_master.h
 Description:           I2C master driver
 Complier:              IAR Embedded Workbench for ARM 8.40.2
 CPU TYPE :             GD32F30x
*************************************************************************
 Copyright (c) 2022 Welling Motor Technology(Shanghai) Co. Ltd.
 All rights reserved.
*************************************************************************
*************************************************************************
 Revising History (ECL of this file):
 M0_20170410, by liyue, create this file;
************************************************************************/
/************************************************************************
 Beginning of File, do not put anything above here except notes
 Compiler Directives:
*************************************************************************/
#ifndef _I2C_MASTER_C_
#define _I2C_MASTER_C_
#endif

/************************************************************************
 Included File
*************************************************************************/
#include "i2c_master.h"
#include "api_rt.h"
#include "gd32f30x_dma.h"
#include "api.h"
/*************************************************************************
 Exported Functions (N/A)
*************************************************************************/

/*************************************************************************
 Function:
 Description:
 Call by:
 Input Variables:
 Output/Return Variables:
 Subroutine Call:
 Reference:
*************************************************************************/
static UWORD i2c_pvt_uwWaitCnt = 0, i2c_pvt_uwWaitCnt2 = 0;
void  i2c_voWaitEEReady(UBYTE SlaveAddr)
{
    /* Wait at least 5ms */
    while (i2c_pvt_uwWaitCnt2 < 2)
    {
        i2c_pvt_uwWaitCnt++;
        if (i2c_pvt_uwWaitCnt == 10000)
        {
            i2c_pvt_uwWaitCnt2++;
            i2c_pvt_uwWaitCnt = 0;
        }
    }
    i2c_pvt_uwWaitCnt2 = 0;
  
//    /* GD MCU has ACK detect function */    
//    ULONG ulTimeCnt = 0;
//    UWORD uwTimeoutNum = 0, uwTimeoutNum2;
//    
//    while(!I2C_EE_ComuFltFlg)
//    {
//        /* write to EEPROM enable*/
//        iGpio_Write(HW_GPIO_I2CWP_PIN,ApiGpio_LowLevel);
//        /* wait until I2C bus is idle */
//        while(i2c_flag_get(I2C0, I2C_FLAG_I2CBSY) && (++ulTimeCnt < I2C_SHORT_TIMEOUT));
//        if(ulTimeCnt == I2C_SHORT_TIMEOUT)
//        {
//           uwTimeoutNum ++;
//        }
//        ulTimeCnt = 0;
//        /* send a start condition to I2C bus */
//        i2c_start_on_bus(I2C0);
//        /* wait until SBSEND bit is set */
//        while((!i2c_flag_get(I2C0, I2C_FLAG_SBSEND)) && (++ulTimeCnt < I2C_SHORT_TIMEOUT));
//        if(ulTimeCnt == I2C_SHORT_TIMEOUT)
//        {
//           uwTimeoutNum ++;
//        }
//        ulTimeCnt = 0;
//        /* send slave address to I2C bus */
//        i2c_master_addressing(I2C0, SlaveAddr, I2C_TRANSMITTER);
//        /* wait until ADDSEND bit is set */
//        while((!((i2c_flag_get(I2C0, I2C_FLAG_ADDSEND)) || (i2c_flag_get(I2C0, I2C_FLAG_AERR))))&& (++ulTimeCnt < I2C_SHORT_TIMEOUT));
//        if(ulTimeCnt < I2C_SHORT_TIMEOUT)
//        {
//            if(i2c_flag_get(I2C0, I2C_FLAG_ADDSEND)) 
//            {
//                ulTimeCnt = 0;
//              /* clear the bit of I2C_FLAG_ADDSEND */
//                i2c_flag_clear(I2C0, I2C_FLAG_ADDSEND);
//                /* send a stop condition to I2C bus */
//                i2c_stop_on_bus(I2C0);
//                /* wait until stop condition generate */ 
//                while((I2C_CTL0(I2C0)&I2C_CTL0_STOP) && (++ulTimeCnt < I2C_SHORT_TIMEOUT));
//                if(ulTimeCnt == I2C_SHORT_TIMEOUT)
//                {
//                   uwTimeoutNum ++;
//                }
//                ulTimeCnt = 0;
//                /* exit the function */
//                I2C_EE_ComuFltFlg = FALSE;
//                break;
//            } 
//            else 
//            {
//                /* clear the bit of I2C_FLAG_AERR */
//                i2c_flag_clear(I2C0, I2C_FLAG_AERR);
//                /* send a stop condition to I2C bus */
//                i2c_stop_on_bus(I2C0);    
//                /* wait until stop condition generate */ 
//                while((I2C_CTL0(I2C0)&I2C_CTL0_STOP) && (++ulTimeCnt < I2C_SHORT_TIMEOUT));
//                if(ulTimeCnt == I2C_SHORT_TIMEOUT)
//                {
//                   uwTimeoutNum ++;
//                }
//                ulTimeCnt = 0;
//            }
//        }
//        else
//        {
//             ulTimeCnt = 0;
//             uwTimeoutNum2 ++;
//             if(uwTimeoutNum2 > 4)
//             {
//                I2C_EE_ComuFltFlg = TRUE;
//                break;
//             }
//        }
//        
//        /* I2C communication timeout fault */
//        if(uwTimeoutNum > 3 )
//        {
//           I2C_EE_ComuFltFlg = TRUE;
//        }        
//    }
//    /* write to EEPROM disable */
//    iGpio_Write(HW_GPIO_I2CWP_PIN,ApiGpio_LowLevel);
    
}

/*************************************************************************
 Function:
 Description:
 Call by:
 Input Variables:
 Output/Return Variables:
 Subroutine Call:
 Reference:
*************************************************************************/
void i2c_voDefaultWriteBuffer(void)
{
    /* Parameter default value write*/ 
    UWORD *I2C_pBuffer;
    UBYTE i;

    I2C_pBuffer = &Syspara2.stMotorPara.uwPolePairs.uwDefault1;
    for (i = 0; i < I2C_MOTOR_PARA_N_WORDS; i++)
    {
        I2C_ubWriteBuffer[I2C_MOTOR_PARA_ARDDR + 2 * i] = (UBYTE)(*I2C_pBuffer >> 8);
        I2C_ubWriteBuffer[I2C_MOTOR_PARA_ARDDR + 2 * i + 1] = (UBYTE)(*I2C_pBuffer);
        I2C_pBuffer += I2C_PBUFFER_NWORDS; /* parasoft-suppress MISRA2004-17_1 "本项目无法更改，后续避免未指向数组的指针运算" */ /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */
    }

    I2C_pBuffer = &Syspara2.stBikePara.uwWheelPerimeter.uwDefault1;
    for (i = 0; i < I2C_BIKE_PARA_N_WORDS; i++)
    {
        I2C_ubWriteBuffer[I2C_BIKE_PARA_ARDDR + 2 * i] = (UBYTE)(*I2C_pBuffer >> 8);
        I2C_ubWriteBuffer[I2C_BIKE_PARA_ARDDR + 2 * i + 1] = (UBYTE)(*I2C_pBuffer);
        I2C_pBuffer += I2C_PBUFFER_NWORDS; /* parasoft-suppress MISRA2004-17_1 "本项目无法更改，后续避免未指向数组的指针运算" */ /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */
    }

    I2C_pBuffer = &Syspara2.stMControlPara.ParaFirstSetFlg.uwDefault1;
    for (i = 0; i < I2C_MCONTROL_PARA_N_WORDS; i++)
    {
        I2C_ubWriteBuffer[I2C_MCONTROL_PARA_ARDDR + 2 * i] = (UBYTE)(*I2C_pBuffer >> 8);
        I2C_ubWriteBuffer[I2C_MCONTROL_PARA_ARDDR + 2 * i + 1] = (UBYTE)(*I2C_pBuffer);
        I2C_pBuffer += I2C_PBUFFER_NWORDS; /* parasoft-suppress MISRA2004-17_1 "本项目无法更改，后续避免未指向数组的指针运算" */ /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */
    }

    I2C_pBuffer = &Syspara2.stSensorPara.uwTorSensorOffsetOrigin.uwDefault1;
    for (i = 0; i < I2C_SENSOR_PARA_N_WORDS; i++)
    {
        I2C_ubWriteBuffer[I2C_SENSOR_PARA_ARDDR + 2 * i] = (UBYTE)(*I2C_pBuffer >> 8);
        I2C_ubWriteBuffer[I2C_SENSOR_PARA_ARDDR + 2 * i + 1] = (UBYTE)(*I2C_pBuffer);
        I2C_pBuffer += I2C_PBUFFER_NWORDS; /* parasoft-suppress MISRA2004-17_1 "本项目无法更改，后续避免未指向数组的指针运算" */ /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */
    }

    I2C_pBuffer = &Syspara2.stAssistPara.uwStartupGain.uwDefault1;
    for (i = 0; i < I2C_ASSIST_PARA_N_WORDS; i++)
    {
        I2C_ubWriteBuffer[I2C_ASSIST_PARA_ARDDR + 2 * i] = (UBYTE)(*I2C_pBuffer >> 8);
        I2C_ubWriteBuffer[I2C_ASSIST_PARA_ARDDR + 2 * i + 1] = (UBYTE)(*I2C_pBuffer);
        I2C_pBuffer += I2C_PBUFFER_NWORDS; /* parasoft-suppress MISRA2004-17_1 "本项目无法更改，后续避免未指向数组的指针运算" */ /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */
    }

    I2C_pWriteBuffer = I2C_ubWriteBuffer;
    I2C_ubWriteBuffer[I2C_MOTOR_PARA_CRC_ARDDR] = (UBYTE)(i2c_uwCRCCcitt(I2C_pWriteBuffer, I2C_MOTOR_PARA_N_BYTES) >> 8);
    I2C_ubWriteBuffer[I2C_MOTOR_PARA_CRC_ARDDR + 1] = (UBYTE)(i2c_uwCRCCcitt(I2C_pWriteBuffer, I2C_MOTOR_PARA_N_BYTES));

    I2C_pWriteBuffer = I2C_ubWriteBuffer + I2C_BIKE_PARA_ARDDR; /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */
    I2C_ubWriteBuffer[I2C_BIKE_PARA_CRC_ARDDR] = (UBYTE)(i2c_uwCRCCcitt(I2C_pWriteBuffer, I2C_BIKE_PARA_N_BYTES) >> 8);
    I2C_ubWriteBuffer[I2C_BIKE_PARA_CRC_ARDDR + 1] = (UBYTE)(i2c_uwCRCCcitt(I2C_pWriteBuffer, I2C_BIKE_PARA_N_BYTES));

    I2C_pWriteBuffer = I2C_ubWriteBuffer + I2C_MCONTROL_PARA_ARDDR; /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */
    I2C_ubWriteBuffer[I2C_MCONTROL_PARA_CRC_ARDDR] = (UBYTE)(i2c_uwCRCCcitt(I2C_pWriteBuffer, I2C_MCONTROL_PARA_N_BYTES) >> 8);
    I2C_ubWriteBuffer[I2C_MCONTROL_PARA_CRC_ARDDR + 1] = (UBYTE)(i2c_uwCRCCcitt(I2C_pWriteBuffer, I2C_MCONTROL_PARA_N_BYTES));

    I2C_pWriteBuffer = I2C_ubWriteBuffer + I2C_SENSOR_PARA_ARDDR; /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */
    I2C_ubWriteBuffer[I2C_SENSOR_PARA_CRC_ARDDR] = (UBYTE)(i2c_uwCRCCcitt(I2C_pWriteBuffer, I2C_SENSOR_PARA_N_BYTES) >> 8);
    I2C_ubWriteBuffer[I2C_SENSOR_PARA_CRC_ARDDR + 1] = (UBYTE)(i2c_uwCRCCcitt(I2C_pWriteBuffer, I2C_SENSOR_PARA_N_BYTES));

    I2C_pWriteBuffer = I2C_ubWriteBuffer + I2C_ASSIST_PARA_ARDDR; /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */
    I2C_ubWriteBuffer[I2C_ASSIST_PARA_CRC_ARDDR] = (UBYTE)(i2c_uwCRCCcitt(I2C_pWriteBuffer, I2C_ASSIST_PARA_N_BYTES) >> 8);
    I2C_ubWriteBuffer[I2C_ASSIST_PARA_CRC_ARDDR + 1] = (UBYTE)(i2c_uwCRCCcitt(I2C_pWriteBuffer, I2C_ASSIST_PARA_N_BYTES));
}
/*************************************************************************
 Function:
 Description:
 Call by:
 Input Variables:
 Output/Return Variables:
 Subroutine Call:
 Reference:
*************************************************************************/
void i2c_voParaWriteBuffer(void)
{
    /* Parameter real value write*/ 
    UWORD *I2C_pBuffer;
    UBYTE i;   
    
    I2C_pBuffer = &Syspara2.stMotorPara.uwPolePairs.uwDefault1;
    for (i = 0; i < I2C_MOTOR_PARA_N_WORDS; i++)
    {
        I2C_ubWriteBuffer[I2C_MOTOR_PARA_ARDDR + 2 * i] = (UBYTE)(*(I2C_pBuffer + 1) >> 8); /* parasoft-suppress MISRA2004-17_1 "本项目无法更改，后续避免未指向数组的指针运算" */ /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */
        I2C_ubWriteBuffer[I2C_MOTOR_PARA_ARDDR + 2 * i + 1] = (UBYTE)(*(I2C_pBuffer + 1)); /* parasoft-suppress MISRA2004-17_1 "本项目无法更改，后续避免未指向数组的指针运算" */ /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */
        I2C_pBuffer += I2C_PBUFFER_NWORDS; /* parasoft-suppress MISRA2004-17_1 "本项目无法更改，后续避免未指向数组的指针运算" */ /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */
    }

    I2C_pBuffer = &Syspara2.stBikePara.uwWheelPerimeter.uwDefault1;
    for (i = 0; i < I2C_BIKE_PARA_N_WORDS; i++)
    {
        I2C_ubWriteBuffer[I2C_BIKE_PARA_ARDDR + 2 * i] = (UBYTE)(*(I2C_pBuffer + 1) >> 8); /* parasoft-suppress MISRA2004-17_1 "本项目无法更改，后续避免未指向数组的指针运算" */ /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */
        I2C_ubWriteBuffer[I2C_BIKE_PARA_ARDDR + 2 * i + 1] = (UBYTE)(*(I2C_pBuffer + 1)); /* parasoft-suppress MISRA2004-17_1 "本项目无法更改，后续避免未指向数组的指针运算" */ /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */
        I2C_pBuffer += I2C_PBUFFER_NWORDS; /* parasoft-suppress MISRA2004-17_1 "本项目无法更改，后续避免未指向数组的指针运算" */ /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */
    }

    I2C_pBuffer = &Syspara2.stMControlPara.ParaFirstSetFlg.uwDefault1;
    for (i = 0; i < I2C_MCONTROL_PARA_N_WORDS; i++)
    {
        I2C_ubWriteBuffer[I2C_MCONTROL_PARA_ARDDR + 2 * i] = (UBYTE)(*(I2C_pBuffer + 1) >> 8); /* parasoft-suppress MISRA2004-17_1 "本项目无法更改，后续避免未指向数组的指针运算" */ /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */
        I2C_ubWriteBuffer[I2C_MCONTROL_PARA_ARDDR + 2 * i + 1] = (UBYTE)(*(I2C_pBuffer + 1)); /* parasoft-suppress MISRA2004-17_1 "本项目无法更改，后续避免未指向数组的指针运算" */ /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */
        I2C_pBuffer += I2C_PBUFFER_NWORDS; /* parasoft-suppress MISRA2004-17_1 "本项目无法更改，后续避免未指向数组的指针运算" */ /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */
    }

    I2C_pBuffer = &Syspara2.stSensorPara.uwTorSensorOffsetOrigin.uwDefault1;
    for (i = 0; i < I2C_SENSOR_PARA_N_WORDS; i++)
    {
        I2C_ubWriteBuffer[I2C_SENSOR_PARA_ARDDR + 2 * i] = (UBYTE)(*(I2C_pBuffer + 1) >> 8); /* parasoft-suppress MISRA2004-17_1 "本项目无法更改，后续避免未指向数组的指针运算" */ /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */
        I2C_ubWriteBuffer[I2C_SENSOR_PARA_ARDDR + 2 * i + 1] = (UBYTE)(*(I2C_pBuffer + 1)); /* parasoft-suppress MISRA2004-17_1 "本项目无法更改，后续避免未指向数组的指针运算" */ /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */
        I2C_pBuffer += I2C_PBUFFER_NWORDS; /* parasoft-suppress MISRA2004-17_1 "本项目无法更改，后续避免未指向数组的指针运算" */ /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */
    }

    I2C_pBuffer = &Syspara2.stAssistPara.uwStartupGain.uwDefault1;
    for (i = 0; i < I2C_ASSIST_PARA_N_WORDS; i++)
    {
        I2C_ubWriteBuffer[I2C_ASSIST_PARA_ARDDR + 2 * i] = (UBYTE)(*(I2C_pBuffer + 1) >> 8); /* parasoft-suppress MISRA2004-17_1 "本项目无法更改，后续避免未指向数组的指针运算" */ /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */
        I2C_ubWriteBuffer[I2C_ASSIST_PARA_ARDDR + 2 * i + 1] = (UBYTE)(*(I2C_pBuffer + 1)); /* parasoft-suppress MISRA2004-17_1 "本项目无法更改，后续避免未指向数组的指针运算" */ /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */
        I2C_pBuffer += I2C_PBUFFER_NWORDS; /* parasoft-suppress MISRA2004-17_1 "本项目无法更改，后续避免未指向数组的指针运算" */ /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */
    }

    I2C_pWriteBuffer = I2C_ubWriteBuffer;
    I2C_ubWriteBuffer[I2C_MOTOR_PARA_CRC_ARDDR] = (UBYTE)(i2c_uwCRCCcitt(I2C_pWriteBuffer, I2C_MOTOR_PARA_N_BYTES) >> 8);
    I2C_ubWriteBuffer[I2C_MOTOR_PARA_CRC_ARDDR + 1] = (UBYTE)(i2c_uwCRCCcitt(I2C_pWriteBuffer, I2C_MOTOR_PARA_N_BYTES));

    I2C_pWriteBuffer = I2C_ubWriteBuffer + I2C_BIKE_PARA_ARDDR; /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */
    I2C_ubWriteBuffer[I2C_BIKE_PARA_CRC_ARDDR] = (UBYTE)(i2c_uwCRCCcitt(I2C_pWriteBuffer, I2C_BIKE_PARA_N_BYTES) >> 8);
    I2C_ubWriteBuffer[I2C_BIKE_PARA_CRC_ARDDR + 1] = (UBYTE)(i2c_uwCRCCcitt(I2C_pWriteBuffer, I2C_BIKE_PARA_N_BYTES));

    I2C_pWriteBuffer = I2C_ubWriteBuffer + I2C_MCONTROL_PARA_ARDDR; /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */
    I2C_ubWriteBuffer[I2C_MCONTROL_PARA_CRC_ARDDR] = (UBYTE)(i2c_uwCRCCcitt(I2C_pWriteBuffer, I2C_MCONTROL_PARA_N_BYTES) >> 8);
    I2C_ubWriteBuffer[I2C_MCONTROL_PARA_CRC_ARDDR + 1] = (UBYTE)(i2c_uwCRCCcitt(I2C_pWriteBuffer, I2C_MCONTROL_PARA_N_BYTES));

    I2C_pWriteBuffer = I2C_ubWriteBuffer + I2C_SENSOR_PARA_ARDDR; /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */
    I2C_ubWriteBuffer[I2C_SENSOR_PARA_CRC_ARDDR] = (UBYTE)(i2c_uwCRCCcitt(I2C_pWriteBuffer, I2C_SENSOR_PARA_N_BYTES) >> 8);
    I2C_ubWriteBuffer[I2C_SENSOR_PARA_CRC_ARDDR + 1] = (UBYTE)(i2c_uwCRCCcitt(I2C_pWriteBuffer, I2C_SENSOR_PARA_N_BYTES));

    I2C_pWriteBuffer = I2C_ubWriteBuffer + I2C_ASSIST_PARA_ARDDR; /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */
    I2C_ubWriteBuffer[I2C_ASSIST_PARA_CRC_ARDDR] = (UBYTE)(i2c_uwCRCCcitt(I2C_pWriteBuffer, I2C_ASSIST_PARA_N_BYTES) >> 8);
    I2C_ubWriteBuffer[I2C_ASSIST_PARA_CRC_ARDDR + 1] = (UBYTE)(i2c_uwCRCCcitt(I2C_pWriteBuffer, I2C_ASSIST_PARA_N_BYTES));
}
/*************************************************************************
 Function:
 Description:
 Call by:
 Input Variables:
 Output/Return Variables:
 Subroutine Call:
 Reference:
*************************************************************************/
void i2c_voHistoryWriteBuffer(void)
{
    UWORD *I2C_pBuffer;
    UBYTE  i;

    I2C_pBuffer = &Syspara2.stHistoryPara.uwAssModSelect.uwDefault1;
    for (i = 0; i < I2C_HISTORY_PARA_N_WORDS; i++)
    {
        I2C_ubHistoyWriteBuffer[I2C_HISTORY_PARA_ARDDR + 2 * i] = (UBYTE)(*(I2C_pBuffer + 1) >> 8); /* parasoft-suppress MISRA2004-17_1 "本项目无法更改，后续避免未指向数组的指针运算" */ /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */
        I2C_ubHistoyWriteBuffer[I2C_HISTORY_PARA_ARDDR + 2 * i + 1] = (UBYTE)(*(I2C_pBuffer + 1)); /* parasoft-suppress MISRA2004-17_1 "本项目无法更改，后续避免未指向数组的指针运算" */ /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */
        I2C_pBuffer += I2C_PBUFFER_NWORDS; /* parasoft-suppress MISRA2004-17_1 "本项目无法更改，后续避免未指向数组的指针运算" */ /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */
    }

    I2C_pHistoryWriteBuffer = I2C_ubHistoyWriteBuffer;
    I2C_ubHistoyWriteBuffer[I2C_HISTORY_PARA_CRC_ARDDR] = (UBYTE)(i2c_uwCRCCcitt(I2C_pHistoryWriteBuffer, I2C_HISTORY_PARA_N_BYTES) >> 8);
    I2C_ubHistoyWriteBuffer[I2C_HISTORY_PARA_CRC_ARDDR + 1] = (UBYTE)(i2c_uwCRCCcitt(I2C_pHistoryWriteBuffer, I2C_HISTORY_PARA_N_BYTES));
}
/*************************************************************************
 Function:
 Description:
 Call by:
 Input Variables:
 Output/Return Variables:
 Subroutine Call:
 Reference:
*************************************************************************/
//static void i2c_voByteWrite2EE(UBYTE SlaveAddr, UBYTE WriteAddr, UBYTE Data) /* parasoft-suppress METRICS-28 "本项目圈复杂度无法更改，后续避免" */
//{
//    ULONG ulTimeCnt = 0;
//    UWORD uwTimeoutNum = 0;
//
//    if(!I2C_EE_ComuFltFlg)
//    {
//        /* write to EEPROM enable*/
//        iGpio_Write(HW_GPIO_I2CWP_PIN,ApiGpio_LowLevel);
//        /* wait until I2C bus is idle */
//        while((i2c_flag_get(I2C0, I2C_FLAG_I2CBSY) != 0) && (ulTimeCnt< I2C_SHORT_TIMEOUT))
//    	{
//        	ulTimeCnt++;
//    	}
//        if(ulTimeCnt == I2C_SHORT_TIMEOUT)
//        {
//           uwTimeoutNum ++;
//        }
//        ulTimeCnt = 0;
//        /* send a start condition to I2C bus */
//        i2c_start_on_bus(I2C0);
//        /* wait until SBSEND bit is set */
//        while((i2c_flag_get(I2C0, I2C_FLAG_SBSEND) == 0) && (ulTimeCnt < I2C_SHORT_TIMEOUT))
//    	{
//        	ulTimeCnt++;
//    	}
//        if(ulTimeCnt == I2C_SHORT_TIMEOUT)
//        {
//           uwTimeoutNum ++;
//        }
//        ulTimeCnt = 0;
//        /* send slave address to I2C bus */
//        i2c_master_addressing(I2C0, SlaveAddr, I2C_TRANSMITTER);
//        /* wait until ADDSEND bit is set */
//        while((i2c_flag_get(I2C0, I2C_FLAG_ADDSEND) == 0) && (ulTimeCnt < I2C_SHORT_TIMEOUT))
//    	{
//        	ulTimeCnt++;
//    	}
//        if(ulTimeCnt == I2C_SHORT_TIMEOUT)
//        {
//           uwTimeoutNum ++;
//        }
//        ulTimeCnt = 0;
//        i2c_flag_clear(I2C0, I2C_FLAG_ADDSEND);
//        /* wait until the transmit data buffer is empty */
//        while((i2c_flag_get(I2C0, I2C_FLAG_TBE) == 0) && (ulTimeCnt < I2C_SHORT_TIMEOUT))
//    	{
//        	ulTimeCnt++;
//    	}
//        if(ulTimeCnt == I2C_SHORT_TIMEOUT)
//        {
//           uwTimeoutNum ++;
//        }
//        ulTimeCnt = 0;
//        /* writeAddr transmission */
//        i2c_data_transmit(I2C0, WriteAddr);
//        /* wait until the BTC bit is set */
//        while((i2c_flag_get(I2C0, I2C_FLAG_BTC) == 0) && (ulTimeCnt < I2C_SHORT_TIMEOUT))
//    	{
//        	ulTimeCnt++;
//    	}
//        if(ulTimeCnt == I2C_SHORT_TIMEOUT)
//        {
//           uwTimeoutNum ++;
//        }
//        ulTimeCnt = 0;
//        /* data transmission */
//        i2c_data_transmit(I2C0, Data);
//        /* wait until the BTC bit is set */
//        while((i2c_flag_get(I2C0, I2C_FLAG_BTC) == 0) && (ulTimeCnt < I2C_SHORT_TIMEOUT))
//    	{
//        	ulTimeCnt++;
//    	}
//        if(ulTimeCnt == I2C_SHORT_TIMEOUT)
//        {
//           uwTimeoutNum ++;
//        }
//        ulTimeCnt = 0;
//        /* send a stop condition to I2C bus */
//        i2c_stop_on_bus(I2C0);
//        /* wait until stop condition generate */
//        while((I2C_CTL0(I2C0)&I2C_CTL0_STOP) && (ulTimeCnt < I2C_SHORT_TIMEOUT))
//        {
//        	ulTimeCnt++;
//        }
//        if(ulTimeCnt == I2C_SHORT_TIMEOUT)
//        {
//           uwTimeoutNum ++;
//        }
//        ulTimeCnt = 0;
//        /* write to EEPROM disable */
//        iGpio_Write(HW_GPIO_I2CWP_PIN,ApiGpio_LowLevel);
//
//        /* I2C EEPROM communication timeout fault */
//        if(uwTimeoutNum > 0)
//        {
//           I2C_EE_ComuFltFlg = TRUE;
//        }
//    }
//    else
//    {}
//}
/*************************************************************************
 Function:
 Description:
 Call by:
 Input Variables:
 Output/Return Variables:
 Subroutine Call:
 Reference:
*************************************************************************/
void i2c_voPageWrite2EE(const UBYTE *pBuffer, UBYTE SlaveAddr, UBYTE WriteAddr, UBYTE NBytesToWrite) /* parasoft-suppress METRICS-28 "本项目圈复杂度无法更改，后续避免" */
{
    ULONG ulTimeCnt = 0;
    UWORD uwTimeoutNum = 0;
    
    if(!I2C_EE_ComuFltFlg)
    {
        /* write to EEPROM enable*/
        iGpio_Write(HW_GPIO_I2CWP_PIN,ApiGpio_HighLevel);
        /* wait until I2C bus is idle */
        while((i2c_flag_get(I2C0, I2C_FLAG_I2CBSY) != 0) && (ulTimeCnt < I2C_SHORT_TIMEOUT))
    	{
        	ulTimeCnt++;
    	}
        if(ulTimeCnt == I2C_SHORT_TIMEOUT)
        {
           uwTimeoutNum ++;
        }
        ulTimeCnt = 0;
        /* send a start condition to I2C bus */
        i2c_start_on_bus(I2C0);
        /* wait until SBSEND bit is set */
        while((i2c_flag_get(I2C0, I2C_FLAG_SBSEND) == 0) && (ulTimeCnt < I2C_SHORT_TIMEOUT))
    	{
        	ulTimeCnt++;
    	}
        if(ulTimeCnt == I2C_SHORT_TIMEOUT)
        {
           uwTimeoutNum ++;
        }
        ulTimeCnt = 0;
        /* send slave address to I2C bus */
        i2c_master_addressing(I2C0, SlaveAddr, I2C_TRANSMITTER);
        /* wait until ADDSEND bit is set */
        while((i2c_flag_get(I2C0, I2C_FLAG_ADDSEND) == 0) && (ulTimeCnt < I2C_SHORT_TIMEOUT))
    	{
        	ulTimeCnt++;
    	}
        if(ulTimeCnt == I2C_SHORT_TIMEOUT)
        {
           uwTimeoutNum ++;
        }
        ulTimeCnt = 0;
        i2c_flag_clear(I2C0, I2C_FLAG_ADDSEND);
        /* wait until the transmit data buffer is empty */
        while((i2c_flag_get(I2C0, I2C_FLAG_TBE) == 0) && (ulTimeCnt < I2C_SHORT_TIMEOUT))
    	{
        	ulTimeCnt++;
    	}
        if(ulTimeCnt == I2C_SHORT_TIMEOUT)
        {
           uwTimeoutNum ++;
        }
        ulTimeCnt = 0;
        /* writeAddr transmission */
        i2c_data_transmit(I2C0, WriteAddr);
        /* wait until the BTC bit is set */
        while((i2c_flag_get(I2C0, I2C_FLAG_BTC) == 0) && (ulTimeCnt < I2C_SHORT_TIMEOUT))
    	{
        	ulTimeCnt++;
    	}
        if(ulTimeCnt == I2C_SHORT_TIMEOUT)
        {
           uwTimeoutNum ++;
        }
        ulTimeCnt = 0;
        /* data transmission */
        while (NBytesToWrite != 0)
        {
        	NBytesToWrite --;
            i2c_data_transmit(I2C0, *pBuffer);
            pBuffer++; /* parasoft-suppress MISRA2004-17_1 "本项目无法更改，后续避免未指向数组的指针运算" */ /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */
            /* wait until the BTC bit is set */
            while((i2c_flag_get(I2C0, I2C_FLAG_BTC) == 0) && (ulTimeCnt < I2C_SHORT_TIMEOUT))
        	{
            	ulTimeCnt++;
        	}
            if(ulTimeCnt == I2C_SHORT_TIMEOUT)
            {
               uwTimeoutNum ++;
            }
            ulTimeCnt = 0;
            /* I2C communication timeout fault */
            if(uwTimeoutNum > 3 )
            {
               I2C_EE_ComuFltFlg = TRUE;
               break;
            }  
        }
        /* send a stop condition to I2C bus */
        i2c_stop_on_bus(I2C0);    
        /* wait until stop condition generate */ 
        while((I2C_CTL0(I2C0)&I2C_CTL0_STOP) && (ulTimeCnt < I2C_SHORT_TIMEOUT))
    	{
        	ulTimeCnt++;
    	}
        if(ulTimeCnt == I2C_SHORT_TIMEOUT)
        {
           uwTimeoutNum ++;
        }
        ulTimeCnt = 0;
         /* I2C EEPROM communication timeout fault */
        if(uwTimeoutNum > 0)
        {
           I2C_EE_ComuFltFlg = TRUE;
        }  
        /* write to EEPROM disable */
        
        iGpio_Write(HW_GPIO_I2CWP_PIN,ApiGpio_LowLevel);
    }
    else
    {}
}
/*************************************************************************
 Function:
 Description:
 Call by:
 Input Variables:
 Output/Return Variables:
 Subroutine Call:
 Reference:
*************************************************************************/
static void i2c_voBufferWrite2EE(const UBYTE *pBuffer, UBYTE SlaveAddr, UBYTE WriteAddr, UBYTE NBytesToWrite)
{
    UBYTE ubNPages = 0, ubNSingleBytes = 0, ubAddr = 0, ubCnt = 0, ubTemp = 0;
    
    ubAddr = WriteAddr % I2C_EE_PAGESIZE_NBYTES;
    ubCnt = I2C_EE_PAGESIZE_NBYTES - ubAddr; // Cnt datas away from page alignment
    ubNPages = NBytesToWrite / I2C_EE_PAGESIZE_NBYTES;
    ubNSingleBytes = NBytesToWrite % I2C_EE_PAGESIZE_NBYTES;    

    if (ubAddr == 0)
    {
        if (ubNPages == 0)
        {
            i2c_voPageWrite2EE(pBuffer, SlaveAddr, WriteAddr, ubNSingleBytes);
            i2c_voWaitEEReady(SlaveAddr);
        }
        else
        {
            while (ubNPages != 0)
            {
            	ubNPages--;
                i2c_voPageWrite2EE(pBuffer, SlaveAddr, WriteAddr, I2C_EE_PAGESIZE_NBYTES);
                i2c_voWaitEEReady(SlaveAddr);
                WriteAddr += I2C_EE_PAGESIZE_NBYTES;
                pBuffer += I2C_EE_PAGESIZE_NBYTES; /* parasoft-suppress MISRA2004-17_1 "本项目无法更改，后续避免未指向数组的指针运算" */ /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */
            }
            if (ubNSingleBytes != 0)
            {
                i2c_voPageWrite2EE(pBuffer, SlaveAddr, WriteAddr, ubNSingleBytes);
                i2c_voWaitEEReady(SlaveAddr);
            }
        }
    }
    else
    {
        if (ubNPages == 0)
        {
            if (ubNSingleBytes > ubCnt)
            {
                ubTemp = ubNSingleBytes - ubCnt;
                i2c_voPageWrite2EE(pBuffer, SlaveAddr, WriteAddr, ubCnt);
                i2c_voWaitEEReady(SlaveAddr);
                WriteAddr += ubCnt;
                pBuffer += ubCnt; /* parasoft-suppress MISRA2004-17_1 "本项目无法更改，后续避免未指向数组的指针运算" */ /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */

                i2c_voPageWrite2EE(pBuffer, SlaveAddr, WriteAddr, ubTemp);
                i2c_voWaitEEReady(SlaveAddr);
            }
            else
            {
                i2c_voPageWrite2EE(pBuffer, SlaveAddr, WriteAddr, NBytesToWrite);
                i2c_voWaitEEReady(SlaveAddr);
            }
        }
        else
        {
            NBytesToWrite -= ubCnt;
            ubNPages = NBytesToWrite / I2C_EE_PAGESIZE_NBYTES;
            ubNSingleBytes = NBytesToWrite % I2C_EE_PAGESIZE_NBYTES;
            if (ubCnt != 0)
            {
                /* Write the remaining bytes of the page where WriteAddr is located */
                i2c_voPageWrite2EE(pBuffer, SlaveAddr, WriteAddr, ubCnt);
                i2c_voWaitEEReady(SlaveAddr);
                WriteAddr += ubCnt;
                pBuffer += ubCnt; /* parasoft-suppress MISRA2004-17_1 "本项目无法更改，后续避免未指向数组的指针运算" */ /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */
            }
            while (ubNPages != 0)
            {
            	ubNPages--;
                i2c_voPageWrite2EE(pBuffer, SlaveAddr, WriteAddr, I2C_EE_PAGESIZE_NBYTES);
                i2c_voWaitEEReady(SlaveAddr);
                WriteAddr += I2C_EE_PAGESIZE_NBYTES;
                pBuffer += I2C_EE_PAGESIZE_NBYTES; /* parasoft-suppress MISRA2004-17_1 "本项目无法更改，后续避免未指向数组的指针运算" */ /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */
            }
            if (ubNSingleBytes != 0)
            {
                i2c_voPageWrite2EE(pBuffer, SlaveAddr, WriteAddr, I2C_EE_PAGESIZE_NBYTES);
                i2c_voWaitEEReady(SlaveAddr);
            }
        }
    }

}

/*************************************************************************
 Function:
 Description:
 Call by:
 Input Variables:
 Output/Return Variables:
 Subroutine Call:
 Reference:
*************************************************************************/
void i2c_voInfoWrite2EE(const I2C_TX_COF *coef, I2C_TX_OUT *out)
{
    UBYTE ubNBytes;
    UBYTE ubReTX1;
    UBYTE ubSlaveAddr;
    UBYTE ubWriteAddr;

    ubNBytes = I2C_TX1_NBYTES;
    ubReTX1 = I2C_RETX1_TIMES;
#if(ubReTX1 >= 2)
     ubReTX1 = 2;
#endif
    ubWriteAddr = 0x00;
    ubSlaveAddr = I2C_SLAVEADDR_BLOCK1;

    while (ubReTX1 != 0)
    {
    	ubReTX1--;
        I2C_pWriteBuffer = I2C_ubWriteBuffer;
        if (ubReTX1 == 1)
        {
            ubSlaveAddr = I2C_SLAVEADDR_BLOCK2;
        }
        if (ubReTX1 == 0)
        {
            ubSlaveAddr = I2C_SLAVEADDR_BLOCK1;
        }
        //i2c_voBufferWrite2EE(I2C_pWriteBuffer, ubSlaveAddr, ubWriteAddr, ubNBytes);
        iI2C_Write(0, ubSlaveAddr, ubWriteAddr, 8, I2C_pWriteBuffer, ubNBytes);
    }

    if ((ubReTX1 == 0) && (I2C_EE_ComuFltFlg != TRUE))
    {
        out->blTX1FinishFlg = TRUE;
    }
    else
    {
        out->blTX1FinishFlg = FALSE;
    }
}
/*************************************************************************
 Function:
 Description:
 Call by:
 Input Variables:
 Output/Return Variables:
 Subroutine Call:
 Reference:
*************************************************************************/
void i2c_voHistoryWrite2EE(const I2C_TX_COF *coef, I2C_TX_OUT *out)
{
    UBYTE ubNBytes;
    UBYTE ubReTX2;
    UBYTE ubSlaveAddr;
    UBYTE ubWriteAddr;

    ubNBytes = I2C_TX2_NBYTES;
    ubReTX2 = I2C_RETX2_TIMES;
#if(ubReTX2 >= 2)
	ubReTX2 = 2;
#endif

    ubSlaveAddr = I2C_SLAVEADDR_BLOCK3;
    ubWriteAddr = 0x00;

    while (ubReTX2 != 0)
    {
    	ubReTX2--;
        I2C_pHistoryWriteBuffer = I2C_ubHistoyWriteBuffer;
        if (ubReTX2 == 1)
        {
            ubSlaveAddr = I2C_SLAVEADDR_BLOCK4;
        }
        if (ubReTX2 == 0)
        {
            ubSlaveAddr = I2C_SLAVEADDR_BLOCK3;
        }
        
        //i2c_voBufferWrite2EE(I2C_pHistoryWriteBuffer, ubSlaveAddr, ubWriteAddr, ubNBytes);
        iI2C_Write(0, ubSlaveAddr, ubWriteAddr, 8, I2C_pHistoryWriteBuffer, ubNBytes);
    }
    if ((ubReTX2 == 0) && (I2C_EE_ComuFltFlg != TRUE))
    {
        out->blTX2FinishFlg = TRUE;
    }
    else
    {
        out->blTX2FinishFlg = FALSE;
    }
}
/*************************************************************************
 Function:
 Description:
 Call by:
 Input Variables:
 Output/Return Variables:
 Subroutine Call:
 Reference:
*************************************************************************/
void i2c_bus_reset(void)
{
    i2c_deinit(I2C0);
    /* configure SDA/SCL for GPIO */
    GPIO_BC(GPIOB) |= GPIO_PIN_6;
    GPIO_BC(GPIOB) |= GPIO_PIN_7;
    gpio_init(GPIOB, GPIO_MODE_OUT_PP, GPIO_OSPEED_50MHZ, GPIO_PIN_6);
    gpio_init(GPIOB, GPIO_MODE_OUT_PP, GPIO_OSPEED_50MHZ, GPIO_PIN_7);
    __NOP();
    __NOP();
    __NOP();
    __NOP();
    __NOP();
    GPIO_BOP(GPIOB) |= GPIO_PIN_6;
    __NOP();
    __NOP();
    __NOP();
    __NOP();
    __NOP();
    GPIO_BOP(GPIOB) |= GPIO_PIN_7;
    /* connect I2C_SCL_PIN to I2C_SCL */
    /* connect I2C_SDA_PIN to I2C_SDA */
    gpio_init(GPIOB, GPIO_MODE_AF_OD, GPIO_OSPEED_50MHZ, GPIO_PIN_6);
    gpio_init(GPIOB, GPIO_MODE_AF_OD, GPIO_OSPEED_50MHZ, GPIO_PIN_7);
    /* configure the I2CX interface */
        /* configure I2C0 clock */
    i2c_clock_config(I2C0, 100000, I2C_DTCY_2);
    
    /* configure I2C0 address */
    i2c_mode_addr_config(I2C0, I2C_I2CMODE_ENABLE, I2C_ADDFORMAT_7BITS, I2C_SLAVEADDR_BLOCK1);
    
    /* enable acknowledge */
    i2c_ack_config(I2C0, I2C_ACK_ENABLE);
    
//    /* enable I2C0 DMA */
//    i2c_dma_config(I2C0, I2C_DMA_ON); 
       
    /* enable I2C0 */
    i2c_enable(I2C0);
}
/*************************************************************************
 Function:
 Description:
 Call by:
 Input Variables:
 Output/Return Variables:
 Subroutine Call:
 Reference:
*************************************************************************/
//  void i2c_voSysparaReadFromEE(I2C_RXCRC_OUT *out) /* parasoft-suppress METRICS-28 "本项目圈复杂度无法更改，后续避免" */
//  {
  
//      UWORD timeout = 0;
//      UBYTE ubRdNBytes = 0, ubRdSlaveAddr = 0, ubRdAddr = 0;
//      UBYTE state = (UBYTE)I2C_START;
//      UBYTE read_cycle = 0;
//      UBYTE ubRdCnt = 2;
   
//      UBYTE i2c_timeout_flag = 0;
//      UBYTE *p_buffer;
    
//       while(ubRdCnt != 0)
//       {
//      	 ubRdCnt--;

//          if (ubRdCnt == 1)
//          {
//              ubRdSlaveAddr = I2C_SLAVEADDR_BLOCK1;
//              ubRdAddr = 0x00;
//              ubRdNBytes = I2C_RX1_NBYTES;           
//              p_buffer = I2C_ubReadBuffer[0];
//              i2c_timeout_flag = 0;
//          }
//          else if (ubRdCnt == 0)
//          {
//              ubRdSlaveAddr = I2C_SLAVEADDR_BLOCK3;
//              ubRdAddr = 0x00;
//              ubRdNBytes = I2C_RX2_NBYTES;
//              p_buffer = I2C_ubReadBuffer[1];
//              i2c_timeout_flag = 0;
//          }
//          else
//          {
//          	//do nothing
//          }
        
//          /* enable acknowledge */
//          i2c_ack_config(I2C0, I2C_ACK_ENABLE);
        
//          while(i2c_timeout_flag ==0)
//          {
//              switch(state) 
//              {
//              case I2C_START:
//                  if(RESET == read_cycle) 
//                  {
//                      /* disable I2C0 */
//                      i2c_disable(I2C0);
//                      /* enable I2C0 */
//                      i2c_enable(I2C0);
//                      /* enable acknowledge */
//                      i2c_ack_config(I2C0, I2C_ACK_ENABLE);
//                      /* i2c master sends start signal only when the bus is idle */
//                      while((i2c_flag_get(I2C0, I2C_FLAG_I2CBSY) != 0) && (timeout < I2C_SHORT_TIMEOUT))
//                      {
//                          timeout++;
//                      }
                    
//                      if(timeout < I2C_SHORT_TIMEOUT) 
//                      {
//                          /* send the start signal */
//                          i2c_start_on_bus(I2C0);
//                          timeout = 0;
//                          state = (UBYTE)I2C_SEND_ADDRESS;
//                      } 
//                      else 
//                      {
//                          i2c_bus_reset();
//                          timeout = 0;
//                          state = (UBYTE)I2C_START;
//                      }
//                  } 
//                  else 
//                  {
//                      i2c_start_on_bus(I2C0);
//                      timeout = 0;
//                      state = (UBYTE)I2C_SEND_ADDRESS;
//                  }
//                  break;
//              case I2C_SEND_ADDRESS:
//                  /* i2c master sends START signal successfully */
//                  while((i2c_flag_get(I2C0, I2C_FLAG_SBSEND) == 0) && (timeout < I2C_SHORT_TIMEOUT))
//                  {
//                      timeout++;
//                  }
//                  if(timeout < I2C_SHORT_TIMEOUT) 
//                  {
//                      if(RESET == read_cycle) 
//                      {
//                          i2c_master_addressing(I2C0, ubRdSlaveAddr, I2C_TRANSMITTER);
//                          state = (UBYTE)I2C_CLEAR_ADDRESS_FLAG;
//                      } 
//                      else 
//                      {
//                          i2c_master_addressing(I2C0, ubRdSlaveAddr, I2C_RECEIVER);
//                          state = (UBYTE)I2C_CLEAR_ADDRESS_FLAG;
//                      }
//                      timeout = 0;
//                  } 
//                  else 
//                  {
//                      timeout = 0;
//                      state = (UBYTE)I2C_START;
//                      read_cycle = 0;
//                  }
//                  break;
//              case I2C_CLEAR_ADDRESS_FLAG:
//                  /* address flag set means i2c slave sends ACK */
//                  while((i2c_flag_get(I2C0, I2C_FLAG_ADDSEND) == 0) && (timeout < I2C_SHORT_TIMEOUT))
//                  {
//                      timeout++;
//                  }
//                  if(timeout < I2C_SHORT_TIMEOUT) 
//                  {
//                      i2c_flag_clear(I2C0, I2C_FLAG_ADDSEND);
//                      timeout = 0;
//                      state = (UBYTE)I2C_TRANSMIT_DATA;
//                  } 
//                  else 
//                  {
//                      timeout = 0;
//                      state = (UBYTE)I2C_START;
//                      read_cycle = 0;   
//                  }
//                  break;
//              case I2C_TRANSMIT_DATA:
//                  if(RESET == read_cycle) 
//                  {
//                      /* wait until the transmit data buffer is empty */
//                      while((i2c_flag_get(I2C0, I2C_FLAG_TBE) == 0) && (timeout < I2C_SHORT_TIMEOUT))
//                      {
//                          timeout++;
//                      }
//                      if(timeout < I2C_SHORT_TIMEOUT) 
//                      {
//                          /* send the EEPROM's internal address to write to : only one byte address */
//                          i2c_data_transmit(I2C0, ubRdAddr);
//                          timeout = 0;
//                      } 
//                      else 
//                      {
//                          timeout = 0;
//                          state = (UBYTE)I2C_START;
//                          read_cycle = 0;    
//                      }
//                      /* wait until BTC bit is set */
//                      while((i2c_flag_get(I2C0, I2C_FLAG_BTC) == 0) && (timeout < I2C_SHORT_TIMEOUT))
//                      {
//                          timeout++;
//                      }
//                      if(timeout < I2C_SHORT_TIMEOUT) 
//                      {
//                          timeout = 0;
//                          state = (UBYTE)I2C_START;
//                          read_cycle++;
//                      }
//                      else 
//                      {
//                          timeout = 0;
//                          state = (UBYTE)I2C_START;
//                          read_cycle = 0;
//                      }
//                  } 
//                  else 
//                  {
//                      /* one byte master reception procedure (polling) */
//                      if(ubRdNBytes < 2) 
//                      {
//                          /* disable acknowledge */
//                          i2c_ack_config(I2C0, I2C_ACK_DISABLE);
//                          /* clear ADDSEND register by reading I2C_STAT0 then I2C_STAT1 register (I2C_STAT0 has already been read) */
//                          i2c_flag_get(I2C0, I2C_FLAG_ADDSEND);
//                          /* send a stop condition to I2C bus*/
//                          i2c_stop_on_bus(I2C0);
//                          /* wait for the byte to be received */
//                          while(i2c_flag_get(I2C0, I2C_FLAG_RBNE) == 0)
//                          {
//                          	// do nothing
//                          }
//                          /* read the byte received from the EEPROM */
//                          *p_buffer = i2c_data_receive(I2C0);
//                          /* decrement the read bytes counter */
//                          ubRdNBytes--;
//                          timeout = 0;
//                          state = (UBYTE)I2C_STOP;
//                      } 
//                      else 
//                      {  /* more than one byte master reception procedure (DMA) */                   
                      
//                          dma_transfer_number_config(DMA0, DMA_CH6, ubRdNBytes);        
//                          DMA_CH6MADDR(DMA0) = (ULONG)p_buffer;
                      
//                          i2c_dma_last_transfer_config(I2C0, I2C_DMALST_ON);
//                          /* enable I2C0 DMA */
//                          i2c_dma_config(I2C0, I2C_DMA_ON);
//                          /* enable DMA0 channel5 */
//                          dma_channel_enable(DMA0, DMA_CH6);
//                          /* wait until BTC bit is set */
//                          while(dma_flag_get(DMA0, DMA_CH6, DMA_FLAG_FTF) == 0)
//                          {
//                          	// do nothing
//                          }

//                          state = (UBYTE)I2C_STOP;
//                      }
//                  }
//                  break;
//              case I2C_STOP:
//                  /* send a stop condition to I2C bus */
//                  i2c_stop_on_bus(I2C0);
//                  /* i2c master sends STOP signal successfully */
//                  while((I2C_CTL0(I2C0) & I2C_CTL0_STOP) && (timeout < I2C_SHORT_TIMEOUT)) 
//                  {
//                      timeout++;
//                  }

//                  if(timeout < I2C_SHORT_TIMEOUT)
//                  {
//                      timeout = 0;                 
//                      i2c_timeout_flag = 1;
//                      state = (UBYTE)I2C_START;
//                      read_cycle = 0;
                   
//                      /* disable DMA0 CH6 */
//                      dma_channel_disable(DMA0, DMA_CH6);
//                      /* disable I2C0 DMA */
//                      i2c_dma_config(I2C0, I2C_DMA_OFF); 
//                      i2c_dma_last_transfer_config(I2C0, I2C_DMALST_OFF);
//                  } 
//                  else 
//                  {
//                       timeout = 0;
//                      //state = I2C_START;
//                       state = (UBYTE)I2C_STOP;
//                       read_cycle = 0;
//                  }
                                              
//                  break;
//              default:
//                  state = (UBYTE)I2C_START;
//                  read_cycle = 0;
//                  i2c_timeout_flag = 1;
//                  timeout = 0;
                
//                  break;
//              }
//          }
        
//       }
    
//      i2c_voReadBufferCRC(out);

//      i2c_voGetValueFrmBuffer(out);

//      out->ReadFinishFlg = TRUE;
    
//  }

void i2c_voSysparaReadFromEE(I2C_RXCRC_OUT *out) /* parasoft-suppress METRICS-28 "本项目圈复杂度无法更改，后续避免" */
{
   UBYTE ubRdNBytes = 0, ubRdSlaveAddr = 0, ubRdAddr = 0;
   UBYTE ubRdCnt = 2;
   UBYTE *p_buffer;
   
    while(ubRdCnt != 0)
    {
   	 ubRdCnt--;

       if (ubRdCnt == 1)
       {
           ubRdSlaveAddr = I2C_SLAVEADDR_BLOCK1;
           ubRdAddr = 0x00;
           ubRdNBytes = I2C_RX1_NBYTES;           
           p_buffer = I2C_ubReadBuffer[0];
       }
       else if (ubRdCnt == 0)
       {
           ubRdSlaveAddr = I2C_SLAVEADDR_BLOCK3;
           ubRdAddr = 0x00;
           ubRdNBytes = I2C_RX2_NBYTES;
           p_buffer = I2C_ubReadBuffer[1];
       }
       else
       {
       	//do nothing
       }

       iI2C_Read(0, ubRdSlaveAddr, ubRdAddr, 8, p_buffer, ubRdNBytes);
   }

    i2c_voReadBufferCRC(out);

    i2c_voGetValueFrmBuffer(out);

    out->ReadFinishFlg = TRUE;
}
/*************************************************************************
 Function:
 Description:
 Call by:
 Input Variables:
 Output/Return Variables:
 Subroutine Call:
 Reference:
*************************************************************************/
UWORD i2c_uwCRCCcitt(const UBYTE *ptubBuf, UWORD length)
{
    UBYTE b = 0;
    UWORD crc = 0xffff;
    UWORD i, j;
    for (i = 0; i < length; i++)
    {
        for (j = 0; j < 8; j++)
        {
            b = (UBYTE)(((ptubBuf[i] << j) & 0x80) ^ ((crc & 0x8000) >> 8)); /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */
            crc <<= 1;
            if (b != 0)
            {
                crc ^= 0x1021; // crc = crc^(0x10000^0x11021)
            }
        }
    }
    return crc;
}
/*************************************************************************
 Function:
 Description:
 Call by:
 Input Variables:
 Output/Return Variables:
 Subroutine Call:
 Reference:
*************************************************************************/
void  i2c_voReadBufferCRC(I2C_RXCRC_OUT *out)
{
    UWORD uwMotorParaCRC, uwBikeParaCRC, uwMControlParaCRC;
    UWORD uwSensorParaCRC, uwAssistParaCRC, uwHistoryParaCRC;
    UWORD uwMotorParaRdCRC, uwBikeParaRdCRC, uwMControlParaRdCRC;
    UWORD uwSensorParaRdCRC, uwAssistParaRdCRC, uwHistoryParaRdCRC;

    I2C_pReadBuffer = I2C_ubReadBuffer[0];
    uwMotorParaCRC = i2c_uwCRCCcitt(I2C_pReadBuffer, I2C_MOTOR_PARA_N_BYTES);
    uwBikeParaCRC = i2c_uwCRCCcitt(I2C_pReadBuffer + I2C_BIKE_PARA_ARDDR, I2C_BIKE_PARA_N_BYTES); /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */
    uwMControlParaCRC = i2c_uwCRCCcitt(I2C_pReadBuffer + I2C_MCONTROL_PARA_ARDDR, I2C_MCONTROL_PARA_N_BYTES); /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */
    uwSensorParaCRC = i2c_uwCRCCcitt(I2C_pReadBuffer + I2C_SENSOR_PARA_ARDDR, I2C_SENSOR_PARA_N_BYTES); /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */
    uwAssistParaCRC = i2c_uwCRCCcitt(I2C_pReadBuffer + I2C_ASSIST_PARA_ARDDR, I2C_ASSIST_PARA_N_BYTES); /* parasoft-suppress MISRA2004-17_4 "本项目无法更改，后续避免非数组索引指针运算" */

    I2C_pReadBuffer = I2C_ubReadBuffer[1];
    uwHistoryParaCRC = i2c_uwCRCCcitt(I2C_pReadBuffer, I2C_HISTORY_PARA_N_BYTES);

    uwMotorParaRdCRC = (UWORD)((UWORD)I2C_ubReadBuffer[0][I2C_MOTOR_PARA_CRC_ARDDR] << 8) + I2C_ubReadBuffer[0][I2C_MOTOR_PARA_CRC_ARDDR + 1];
    uwBikeParaRdCRC = (UWORD)((UWORD)I2C_ubReadBuffer[0][I2C_BIKE_PARA_CRC_ARDDR] << 8) + I2C_ubReadBuffer[0][I2C_BIKE_PARA_CRC_ARDDR + 1];
    uwMControlParaRdCRC = (UWORD)((UWORD)I2C_ubReadBuffer[0][I2C_MCONTROL_PARA_CRC_ARDDR] << 8) + I2C_ubReadBuffer[0][I2C_MCONTROL_PARA_CRC_ARDDR + 1];
    uwSensorParaRdCRC = (UWORD)((UWORD)I2C_ubReadBuffer[0][I2C_SENSOR_PARA_CRC_ARDDR] << 8) + I2C_ubReadBuffer[0][I2C_SENSOR_PARA_CRC_ARDDR + 1];
    uwAssistParaRdCRC = (UWORD)((UWORD)I2C_ubReadBuffer[0][I2C_ASSIST_PARA_CRC_ARDDR] << 8) + I2C_ubReadBuffer[0][I2C_ASSIST_PARA_CRC_ARDDR + 1];
    uwHistoryParaRdCRC = (UWORD)((UWORD)I2C_ubReadBuffer[1][I2C_HISTORY_PARA_CRC_ARDDR] << 8) + I2C_ubReadBuffer[1][I2C_HISTORY_PARA_CRC_ARDDR + 1];

    if (uwMotorParaCRC != uwMotorParaRdCRC)
    {
        out->blMotorParaFltFlg = TRUE;
    }
    if (uwBikeParaCRC != uwBikeParaRdCRC)
    {
        out->blBikeParaFltFlg = TRUE;
    }
    if (uwMControlParaCRC != uwMControlParaRdCRC)
    {
        out->blMControlParaFltFlg = TRUE;
    }
    if (uwSensorParaCRC != uwSensorParaRdCRC)
    {
        out->blSensorParaFltFlg = TRUE;
    }
    if (uwAssistParaCRC != uwAssistParaRdCRC)
    {
        out->blAssistParaFltFlg = TRUE;
    }
    if (uwHistoryParaCRC != uwHistoryParaRdCRC)
    {
        out->blHistoryParaFltFlg = TRUE;
    }
}
/*************************************************************************
 Function:
 Description:
 Call by:
 Input Variables:
 Output/Return Variables:
 Subroutine Call:
 Reference:
*************************************************************************/
void i2c_voGetValueFrmBuffer(const I2C_RXCRC_OUT *out)
{

    UBYTE j = 0;

    if (out->blMotorParaFltFlg != TRUE)
    {
        for (j = 0; j < I2C_MOTOR_PARA_N_WORDS; j++)
        {
            I2C_uwMotorParaRead[j] = (UWORD)((UWORD)I2C_ubReadBuffer[0][I2C_MOTOR_PARA_ARDDR + 2 * j] << 8) + I2C_ubReadBuffer[0][I2C_MOTOR_PARA_ARDDR + 2 * j + 1];
        }
    }
    else
    {}

    if (out->blBikeParaFltFlg != TRUE)
    {
        for (j = 0; j < I2C_BIKE_PARA_N_WORDS; j++)
        {
            I2C_uwBikeParaRead[j] = (UWORD)((UWORD)I2C_ubReadBuffer[0][I2C_BIKE_PARA_ARDDR + 2 * j] << 8) + I2C_ubReadBuffer[0][I2C_BIKE_PARA_ARDDR + 2 * j + 1];
        }
    }
    else
    {}

    if (out->blMControlParaFltFlg != TRUE)
    {
        for (j = 0; j < I2C_MCONTROL_PARA_N_WORDS; j++)
        {
            I2C_uwMControlRead[j] =
            		(UWORD)((UWORD)I2C_ubReadBuffer[0][I2C_MCONTROL_PARA_ARDDR + 2 * j] << 8) + I2C_ubReadBuffer[0][I2C_MCONTROL_PARA_ARDDR + 2 * j + 1];
        }
    }
    else
    {}

    if (out->blSensorParaFltFlg != TRUE)
    {
        for (j = 0; j < I2C_SENSOR_PARA_N_WORDS; j++)
        {
            I2C_uwSensorRead[j] = (UWORD)((UWORD)I2C_ubReadBuffer[0][I2C_SENSOR_PARA_ARDDR + 2 * j] << 8) + I2C_ubReadBuffer[0][I2C_SENSOR_PARA_ARDDR + 2 * j + 1];
        }
    }
    else
    {}

    if (out->blAssistParaFltFlg != TRUE)
    {
        for (j = 0; j < I2C_ASSIST_PARA_N_WORDS; j++)
        {
            I2C_uwAssistParaRead[j] =
            		(UWORD)((UWORD)I2C_ubReadBuffer[0][I2C_ASSIST_PARA_ARDDR + 2 * j] << 8) + I2C_ubReadBuffer[0][I2C_ASSIST_PARA_ARDDR + 2 * j + 1];
        }
    }
    else
    {}

    if (out->blHistoryParaFltFlg != TRUE)
    {
        for (j = 0; j < I2C_HISTORY_PARA_N_WORDS; j++)
        {
            I2C_uwHistoryParaRead[j] =
            		(UWORD)((UWORD)I2C_ubReadBuffer[1][I2C_HISTORY_PARA_ARDDR + 2 * j] << 8) + I2C_ubReadBuffer[1][I2C_HISTORY_PARA_ARDDR + 2 * j + 1];
        }
    }
    else
    {}

    Syspara2.stMotorPara.uwPolePairs.uwReal = I2C_uwMotorParaRead[0];
    Syspara2.stMotorPara.uwRsmOhm.uwReal = I2C_uwMotorParaRead[1];
    Syspara2.stMotorPara.uwLduH.uwReal = I2C_uwMotorParaRead[2];
    Syspara2.stMotorPara.uwLquH.uwReal = I2C_uwMotorParaRead[3];
    Syspara2.stMotorPara.uwFluxmWb.uwReal = I2C_uwMotorParaRead[4];
    Syspara2.stMotorPara.uwIdMaxA.uwReal = I2C_uwMotorParaRead[5];
    Syspara2.stMotorPara.uwIdMinA.uwReal = I2C_uwMotorParaRead[6];
    Syspara2.stMotorPara.uwRSpdRpm.uwReal = I2C_uwMotorParaRead[7];
    Syspara2.stMotorPara.uwRPwrWt.uwReal = I2C_uwMotorParaRead[8];
    Syspara2.stMotorPara.uwRCurA.uwReal = I2C_uwMotorParaRead[9];
    Syspara2.stMotorPara.uwRVolV.uwReal = I2C_uwMotorParaRead[10];
    Syspara2.stMotorPara.uwJD.uwReal = I2C_uwMotorParaRead[11];
    Syspara2.stMotorPara.uwTorMaxNm.uwReal = I2C_uwMotorParaRead[12];

    Syspara2.stBikePara.uwWheelPerimeter.uwReal = I2C_uwBikeParaRead[0];
    Syspara2.stBikePara.uwMechRationMotor.uwReal = I2C_uwBikeParaRead[1];
    Syspara2.stBikePara.uwAssistMaxSpdKmH.uwReal = I2C_uwBikeParaRead[2];
    Syspara2.stBikePara.uwThrottleMaxSpdKmH.uwReal = I2C_uwBikeParaRead[3];
    Syspara2.stBikePara.uwNmFrontChainring.uwReal = I2C_uwBikeParaRead[4];
    Syspara2.stBikePara.uwNmBackChainring.uwReal = I2C_uwBikeParaRead[5];
    Syspara2.stBikePara.uwAssistSelect1.uwReal = I2C_uwBikeParaRead[6];
    Syspara2.stBikePara.uwAssistSelect2.uwReal = I2C_uwBikeParaRead[7];
    Syspara2.stBikePara.uwLightVoltage.uwReal = I2C_uwBikeParaRead[8];
    Syspara2.stBikePara.swDeltPerimeter.swReal = (SWORD)I2C_uwBikeParaRead[9];
    Syspara2.stBikePara.uwStartMode.uwReal = I2C_uwBikeParaRead[10];
    Syspara2.stBikePara.uwAutoPowerOffTime.uwReal = I2C_uwBikeParaRead[11];

    Syspara2.stMControlPara.ParaFirstSetFlg.uwReal = I2C_uwMControlRead[0];
    Syspara2.stMControlPara.SpiOffsetFirstSetFlg.uwReal = I2C_uwMControlRead[1];
    Syspara2.stMControlPara.uwSPIPosOffsetOrigin.uwReal = I2C_uwMControlRead[2];
    Syspara2.stMControlPara.uwSPIPosOffsetNow.uwReal = I2C_uwMControlRead[3];
    Syspara2.stMControlPara.uwIPeakMaxA.uwReal = I2C_uwMControlRead[4];
    Syspara2.stMControlPara.uwAlamOCurA.uwReal = I2C_uwMControlRead[5];
    Syspara2.stMControlPara.uwAlamOVolV.uwReal = I2C_uwMControlRead[6];
    Syspara2.stMControlPara.uwAlamUVolV.uwReal = I2C_uwMControlRead[7];
    Syspara2.stMControlPara.uwAlamOverSpdRpm.uwReal = I2C_uwMControlRead[8];
    Syspara2.stMControlPara.uwAlamOverHeatCe.uwReal = I2C_uwMControlRead[9];
    Syspara2.stMControlPara.uwAlamRecHeatCe.uwReal = I2C_uwMControlRead[10];
    Syspara2.stMControlPara.uwPwrLimitStartCe.uwReal = I2C_uwMControlRead[11];

    Syspara2.stSensorPara.uwTorSensorOffsetOrigin.uwReal = I2C_uwSensorRead[0];
    Syspara2.stSensorPara.uwTorSensorOffsetNow1.uwReal = I2C_uwSensorRead[1];
    Syspara2.stSensorPara.uwTorSensorOffsetNow2.uwReal = I2C_uwSensorRead[2];
    Syspara2.stSensorPara.uwTorSensorOffsetNow3.uwReal = I2C_uwSensorRead[3];
    Syspara2.stSensorPara.uwTorSensorOffsetNow4.uwReal = I2C_uwSensorRead[4];
    Syspara2.stSensorPara.uwBikeTorMaxNm.uwReal = I2C_uwSensorRead[5];
    Syspara2.stSensorPara.uwBikeTor1StepRealNm.uwReal = I2C_uwSensorRead[6];
    Syspara2.stSensorPara.uwBikeTor1StepADC.uwReal = I2C_uwSensorRead[7];
    Syspara2.stSensorPara.uwBikeTor2StepRealNm.uwReal = I2C_uwSensorRead[8];
    Syspara2.stSensorPara.uwBikeTor2StepADC.uwReal = I2C_uwSensorRead[9];
    Syspara2.stSensorPara.uwBikeTor3StepRealNm.uwReal = I2C_uwSensorRead[10];
    Syspara2.stSensorPara.uwBikeTor3StepADC.uwReal = I2C_uwSensorRead[11];
    Syspara2.stSensorPara.uwBikeTor4StepRealNm.uwReal = I2C_uwSensorRead[12];
    Syspara2.stSensorPara.uwBikeTor4StepADC.uwReal = I2C_uwSensorRead[13];
    Syspara2.stSensorPara.uwCadSensorPulseNm.uwReal = I2C_uwSensorRead[14];
    Syspara2.stSensorPara.uwBikeSpdSensorPulseNm.uwReal = I2C_uwSensorRead[15];

    Syspara2.stAssistPara.uwStartupGain.uwReal = I2C_uwAssistParaRead[0];
    Syspara2.stAssistPara.uwStartcruiseGain.uwReal = I2C_uwAssistParaRead[1];
    Syspara2.stAssistPara.uwAssistStartNm.uwReal = I2C_uwAssistParaRead[2];
    Syspara2.stAssistPara.uwAssistStopNm.uwReal = I2C_uwAssistParaRead[3];
    Syspara2.stAssistPara.uwStartUpGainStep.uwReal = I2C_uwAssistParaRead[4];
    Syspara2.stAssistPara.uwStartUpCadNm.uwReal = I2C_uwAssistParaRead[5];
    Syspara2.stAssistPara.uwTorLPFCadNm.uwReal = I2C_uwAssistParaRead[6];
    Syspara2.stAssistPara.uwSpeedAssistSpdRpm.uwReal = I2C_uwAssistParaRead[7];
    Syspara2.stAssistPara.uwSpeedAssistIMaxA.uwReal = I2C_uwAssistParaRead[8];
    Syspara2.stAssistPara.uwAssistLimitBikeSpdStart.uwReal = I2C_uwAssistParaRead[9];
    Syspara2.stAssistPara.uwAssistLimitBikeSpdStop.uwReal = I2C_uwAssistParaRead[10];
    Syspara2.stAssistPara.uwCadenceAssistWeight.uwReal = I2C_uwAssistParaRead[11];

    Syspara2.stHistoryPara.uwAssModSelect.uwReal = I2C_uwHistoryParaRead[0];
    Syspara2.stHistoryPara.uwOpenTimes.uwReal = I2C_uwHistoryParaRead[1];
    Syspara2.stHistoryPara.uwUsedTimeH.uwReal = I2C_uwHistoryParaRead[2];
    Syspara2.stHistoryPara.uwUsedTimeL.uwReal = I2C_uwHistoryParaRead[3];
    Syspara2.stHistoryPara.uwNTCTempMaxCe.uwReal = I2C_uwHistoryParaRead[4];
    Syspara2.stHistoryPara.uwNTCTempMinCe.uwReal = I2C_uwHistoryParaRead[5];
    Syspara2.stHistoryPara.uwAlamHOcurTimes.uwReal = I2C_uwHistoryParaRead[6];
    Syspara2.stHistoryPara.uwAlamSOcurTimes.uwReal = I2C_uwHistoryParaRead[7];
    Syspara2.stHistoryPara.uwAlamOHeatTimes.uwReal = I2C_uwHistoryParaRead[8];
    Syspara2.stHistoryPara.uwAlamRotorLockTimes.uwReal = I2C_uwHistoryParaRead[9];
    Syspara2.stHistoryPara.uwAlamPhsLossTimes.uwReal = I2C_uwHistoryParaRead[10];
    Syspara2.stHistoryPara.uwAlamOVolTimes.uwReal = I2C_uwHistoryParaRead[11];
    Syspara2.stHistoryPara.uwAlamUVolTimes.uwReal = I2C_uwHistoryParaRead[12];
    Syspara2.stHistoryPara.uwAlamComOTimeTimes.uwReal = I2C_uwHistoryParaRead[13];

    Syspara2.stHistoryPara.uwG1AvgPwrConsumption.uwReal = I2C_uwHistoryParaRead[14];
    Syspara2.stHistoryPara.uwG2AvgPwrConsumption.uwReal = I2C_uwHistoryParaRead[15];
    Syspara2.stHistoryPara.uwG3AvgPwrConsumption.uwReal = I2C_uwHistoryParaRead[16];
    Syspara2.stHistoryPara.uwG4AvgPwrConsumption.uwReal = I2C_uwHistoryParaRead[17];
    Syspara2.stHistoryPara.uwG5AvgPwrConsumption.uwReal = I2C_uwHistoryParaRead[18];

    Syspara2.stHistoryPara.uwODOTripH.uwReal = I2C_uwHistoryParaRead[19];
    Syspara2.stHistoryPara.uwODOTripL.uwReal = I2C_uwHistoryParaRead[20];
    Syspara2.stHistoryPara.uwODOTimeH.uwReal = I2C_uwHistoryParaRead[21];
    Syspara2.stHistoryPara.uwODOTimeL.uwReal = I2C_uwHistoryParaRead[22];

    Syspara2.stHistoryPara.uwTripSumH.uwReal = I2C_uwHistoryParaRead[23];
    Syspara2.stHistoryPara.uwTripSumL.uwReal = I2C_uwHistoryParaRead[24];
    Syspara2.stHistoryPara.uwTripSumTimeH.uwReal = I2C_uwHistoryParaRead[25];
    Syspara2.stHistoryPara.uwTripSumTimeL.uwReal = I2C_uwHistoryParaRead[26];

    Syspara2.stHistoryPara.uwTorSensorAlamTimes.uwReal = I2C_uwHistoryParaRead[27];
    Syspara2.stHistoryPara.uwCadSensorAlamTimes.uwReal = I2C_uwHistoryParaRead[28];
    Syspara2.stHistoryPara.uwBikeSpdSensorAlamTimes.uwReal = I2C_uwHistoryParaRead[29];
    Syspara2.stHistoryPara.uwPosSensorAlamTimes.uwReal = I2C_uwHistoryParaRead[30];

}
/*************************************************************************
 Function:
 Description:
 Call by:
 Input Variables:
 Output/Return Variables:
 Subroutine Call:
 Reference:
*************************************************************************/
void  i2c_voWriteTest(void)
{
    UBYTE WriteBuffer[4];
    UBYTE  *pBuffer;
    
    WriteBuffer[0] = 0x06;
    WriteBuffer[1] = 0x08;  
    WriteBuffer[2] = 0x0A;
    WriteBuffer[3] = 0x01;
    pBuffer = WriteBuffer;
    i2c_voPageWrite2EE(pBuffer, I2C_SLAVEADDR_BLOCK1, 0x00, 4);
}

/*************************************************************************
 Function:
 Description:
 Call by:
 Input Variables:
 Output/Return Variables:
 Subroutine Call:
 Reference:
*************************************************************************/
void  i2c_voReadTest(void) /* parasoft-suppress METRICS-28 "本项目圈复杂度无法更改，后续避免" */
{
    UBYTE  ReadBuffer[6];
    
    ULONG ulTimeCnt = 0;
    UWORD uwTimeoutNum = 0;
    UWORD uwReadNBytes = 6;
    
    /* wait until I2C bus is idle */
    while((i2c_flag_get(I2C0, I2C_FLAG_I2CBSY) != 0) && (ulTimeCnt < I2C_SHORT_TIMEOUT))
    {
    	ulTimeCnt++;
    }
    if(ulTimeCnt == I2C_SHORT_TIMEOUT)
    {
       uwTimeoutNum ++;
    }
    ulTimeCnt = 0;
    /* send a start condition to I2C bus */
    i2c_start_on_bus(I2C0);
    /* wait until SBSEND bit is set */
    while((i2c_flag_get(I2C0, I2C_FLAG_SBSEND) == 0) && (ulTimeCnt < I2C_SHORT_TIMEOUT))
    {
    	ulTimeCnt++;
    }
    if(ulTimeCnt == I2C_SHORT_TIMEOUT)
    {
       uwTimeoutNum ++;
    }
    ulTimeCnt = 0;
    /* send slave address to I2C bus */
    i2c_master_addressing(I2C0, I2C_SLAVEADDR_BLOCK1, I2C_TRANSMITTER);
    /* wait until ADDSEND bit is set */
    while((i2c_flag_get(I2C0, I2C_FLAG_ADDSEND) == 0) && (ulTimeCnt < I2C_SHORT_TIMEOUT))
    {
    	ulTimeCnt++;
    }
    if(ulTimeCnt == I2C_SHORT_TIMEOUT)
    {
       uwTimeoutNum ++;
    }
    ulTimeCnt = 0;
    /* clear ADDSEND bit */
    i2c_flag_clear(I2C0, I2C_FLAG_ADDSEND);
    /* wait until the TBE bit is set */
    while((i2c_flag_get(I2C0, I2C_FLAG_TBE) == 0) && (ulTimeCnt < I2C_SHORT_TIMEOUT))
    {
    	ulTimeCnt++;
    }
    if(ulTimeCnt == I2C_SHORT_TIMEOUT)
    {
       uwTimeoutNum ++;
    }
    ulTimeCnt = 0;
    /* readAddr transmission */
    i2c_data_transmit(I2C0, 0x00);
    /* wait until the BTC bit is set */
    while((i2c_flag_get(I2C0, I2C_FLAG_BTC) == 0) && (ulTimeCnt < I2C_SHORT_TIMEOUT))
    {
    	ulTimeCnt++;
    }
    if(ulTimeCnt == I2C_SHORT_TIMEOUT)
    {
       uwTimeoutNum ++;
    }
    ulTimeCnt = 0;
    
    /* send a start condition to I2C bus */
    i2c_start_on_bus(I2C0);
    /* wait until SBSEND bit is set */
    while((i2c_flag_get(I2C0, I2C_FLAG_SBSEND) == 0) && (ulTimeCnt < I2C_SHORT_TIMEOUT))
    {
    	ulTimeCnt++;
    }
    if(ulTimeCnt == I2C_SHORT_TIMEOUT)
    {
       uwTimeoutNum ++;
    }
    ulTimeCnt = 0;
    /* send slave address to I2C bus */
    i2c_master_addressing(I2C0, I2C_SLAVEADDR_BLOCK1, I2C_RECEIVER);
    /* wait until ADDSEND bit is set */
    while((i2c_flag_get(I2C0, I2C_FLAG_ADDSEND) == 0)&& (ulTimeCnt < I2C_SHORT_TIMEOUT))
    {
    	ulTimeCnt++;
    }
    if(ulTimeCnt == I2C_SHORT_TIMEOUT)
    {
       uwTimeoutNum ++;
    }
    ulTimeCnt = 0;
    /* clear ADDSEND bit */
    i2c_flag_clear(I2C0, I2C_FLAG_ADDSEND);
    
    while(uwReadNBytes != 0)
    {
    	uwReadNBytes--;
        if(2 == uwReadNBytes) 
        {
            /* wait until BTC bit is set */
            while((i2c_flag_get(I2C0, I2C_FLAG_BTC) == 0) && (ulTimeCnt < I2C_SHORT_TIMEOUT))
            {
            	ulTimeCnt++;
            }
            if(ulTimeCnt == I2C_SHORT_TIMEOUT)
            {
               uwTimeoutNum ++;
            }
            ulTimeCnt = 0;
            /* disable acknowledge */
            i2c_ack_config(I2C0, I2C_ACK_DISABLE);
        }
        if(1 == uwReadNBytes) 
        {
            /* wait until BTC bit is set */
            while((i2c_flag_get(I2C0, I2C_FLAG_BTC) == 0) && (ulTimeCnt < I2C_SHORT_TIMEOUT))
            {
            	ulTimeCnt++;
            }
            if(ulTimeCnt == I2C_SHORT_TIMEOUT)
            {
               uwTimeoutNum ++;
            }
            ulTimeCnt = 0;
            /* send a stop condition to I2C bus */
            i2c_stop_on_bus(I2C0);
         }
        
        while((i2c_flag_get(I2C0, I2C_FLAG_RBNE) == 0) && (ulTimeCnt < I2C_SHORT_TIMEOUT))
        {
        	ulTimeCnt++;
        }
        if(ulTimeCnt == I2C_SHORT_TIMEOUT)
        {
           uwTimeoutNum ++;
        }
        ulTimeCnt = 0;
        ReadBuffer[5 - uwReadNBytes] = i2c_data_receive(I2C0);
    }
       
    
    /* wait until stop condition generate */ 
    while((I2C_CTL0(I2C0)&I2C_CTL0_STOP) && (ulTimeCnt < I2C_SHORT_TIMEOUT))
    {
    	ulTimeCnt++;
    }
    if(ulTimeCnt == I2C_SHORT_TIMEOUT)
    {
       uwTimeoutNum ++;
    }
    ulTimeCnt = 0;
    
    if(uwTimeoutNum > 3)
    {
        I2C_EE_ComuFltFlg = TRUE;
    }
}
/*************************************************************************
 Copyright (c) 2018 Welling Motor Technology(Shanghai) Co. Ltd.
 All rights reserved.
*************************************************************************/
#ifdef _I2C_MASTER_C_
#undef _I2C_MASTER_C_ /* parasoft-suppress MISRA2004-19_6 "本项目中无法更改，后续避免使用" */
#endif
/*************************************************************************
 End of this File (EOF)!
 Do not put anything after this part!
*************************************************************************/